DESIGNER SOLUTIONS
MANUAL PART NUMBER: 400-0133-003
CNK221/CNK231
CABLE-NOOK JR.™
INTERCONNECT BOX
USER’S GUIDE
DESIGNER SOLUTIONS
PRECAUTIONS / SAFETY WARNINGS
1
1.3 CLEANING
· Surfaces should be cleaned with a dry cloth.
Never use strong detergents or solvents, such
as alcohol or thinner. Do not use a wet cloth or
water to clean the unit.
Please read this manual carefully before using your
Tabletop Cable-Nook Jr.™ Interconnect Box. Keep
this manual handy for future reference. These
safety instructions are to ensure the long life of
your Cable-Nook Jr.™ and to prevent fire and shock
hazard. Please read them carefully and heed all
warnings.
1.4 FCC / CE NOTICE
· This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
1.1 GENERAL
· Unauthorized personnel shall not open the unit
since there are high-voltage components inside.
· Qualified ALTINEX service personnel, or their
authorized representatives must perform all
service.
· This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
1.2 INSTALLATION
· For best results, place the Tabletop Cable-Nook
Jr.™ Interconnect Box in a dry area away from
dust and moisture.
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
· To prevent fire or shock, do not expose this unit
to rain or moisture. Do not place the Tabletop
Cable-Nook Jr.™ Interconnect Box in direct
sunlight, near heaters or heat radiating
appliances, or near any liquid. Exposure to
direct sunlight, smoke, or steam can harm
internal components.
· Handle
the
Tabletop
Cable-Nook
Jr.™
Interconnect Box carefully. Never lay the Cable-
Nook Jr.™ on the thin bezel lip. Dropping, jarring
or striking the bezel may damage it.
· Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
· Never place fingers inside the openings in the
sides of the unit or along the bezel edges. The
sharp edges may cause serious injury.
ABOUT YOUR CABLE-NOOK Jr.™
2
· Do not place heavy objects on top of the
Tabletop Cable-Nook Jr.™ Interconnect Box. Do
not use excessive force to push down on the top
of the unit.
The Tabletop Cable-Nook Jr.™ Interconnect Box is
designed for installation into a conference room or
boardroom table. The Cable-Nook Jr.™ provides a
means of connecting audio, video, and other
multimedia sources into a presentation system. It is
ideal for use with ALTINEX computer video
interfaces or distribution amplifiers.
· Tabletop cutout dimensions and templates can
be obtained from the Altinex website at
The Tabletop Cable-Nook Jr.™ Interconnect Box
provides a simple yet effective way of storing and
hiding cables, eliminating the obstruction. The
2
DESIGNER SOLUTIONS
cables can remain connected to a presentation
system, enabling the user to connect them to
different media sources needed for a presentation.
After the presentation, the cables may be returned
to the Cable-Nook Jr.™ for safe storage.
The Tabletop Cable-Nook Jr.™ Interconnect Box is
designed for use with tabletops up to three inches
thick. Optional insert plates are available to secure
the cable ends or to add connections for a variety
of multimedia and power cables. The insert plates
can be adjusted to fit a variety of cable sizes. The
height of the insert plates can also be adjusted by
changing the height of the interior bracket mounts
in the Cable-Nook Jr.™.
All specifications are subject to change without
information.
FEATURES/DESCRIPTION
CNK221/CNK231
MECHANICAL
Bezel Width, inches [mm]
Bezel Depth, inches [mm]
Bezel Dia. (CNK231), inches [mm]
Height (cover open), inches [mm]
Height (cover closed), inches [mm]
Standard Finish
4.60” [117mm]
4.90” [124.5mm]
5.75” [146mm]
7.42” [188mm]
4.79” [122mm]
Matte Black
10°C-35°C
T° Operating
T° Maximum
50°C
90% non-
condensing
Humidity
Table 1. Cable-Nook Jr.™ Mechanical
TECHNICAL SPECIFICATIONS
3
3
DESIGNER SOLUTIONS
DESCRIPTION OF CABLE-NOOK Jr.™
4
Diagram 1: Dimensions
(All dimensions are ± .03 [± 0.8mm])
BRACKET MOUNTS
FOR INSERT PLATES
4.90"
[124.5mm]
INTERIOR VIEW
(Cover Removed)
4.60"
[117mm]
5.75" DIA.
[146mm DIA.]
CNK221
Dimensions
CNK231
Dimensions
SIDE VIEW
2.68" [68mm]
Opened
4.79"
4.76"
[122mm]
(To Top of Lip)
[121mm]
(Below Lip)
3.48"
[88mm]
3.75"
[95mm]
3.75"
[95mm]
4.08"
[104mm]
4.10"
[104mm]
5.25" DIA.
[133mm DIA.]
4.40"
[112mm]
For tabletop cutout dimensions, see www.altinex.com.
4
DESIGNER SOLUTIONS
APPLICATION DIAGRAM
5
Diagram 2: Application Example
Laptop
Computer
Inputs
Computer Video + Audio
Interface
Network
Telephone
Video + Audio
AC Power
CNK221
CNK231
To Projector,
Racks, or
5
DESIGNER SOLUTIONS
INSTALLING YOUR CABLE-NOOK Jr.™
6
OPERATION
7
Step 1. Cut an opening in the table’s surface.
dimensions and templates. The tabletop
Lift the Cable-Nook Jr.™ ’s cover to install or route
cables. If the cables need to be connected
while the lid is closed, route the cables
through the open space in the front of the
lid. Unconnected cables may be stored
inside the Cable-Nook Jr.™. until they are
needed.
thickness must be 3 inches [76mm] or less.
Always confirm dimensions before
cutting the table to ensure that the
specifications have not changed.
Step 2. Adjust the bracket mounts inside the unit to
suit your needs. CAUTION! Do not handle
the unit by the bezel’s thin lip or lay it
on it’s side on the lip. The thin bezel lip
is very sharp and can be easily dented
or bent. Handle the unit by the housing
portion only. Remove the two screws
securing each bracket to the interior
housing if necessary to place them at the
level that you require using the holes on
the side of the housing. Replace the
screws on each bracket mount after
making sure that they are at exactly the
same level.
Step 3. Insert the Cable-Nook Jr.™ unit into the
tabletop cutout. Place a mounting bracket
with the thumbscrew installed into the
support mounts on each side of the
housing as shown in Figure 1. With the
mounting brackets installed, turn the
thumbscrews until the ends of the screws
begin to push against the bottom of the
table. Tighten the screws until the unit is
secure. Do not over-tighten.
TABLETOP
SUPPORT BRACKET
THUMBSCREW
Figure 1: Securing the Cable-Nook Jr.™ to the
tabletop.
SUPPORT MOUNTS
SUPPORT MOUNTS
HOUSING
6
DESIGNER SOLUTIONS
ACCESSORIES
Model No.
8
ALTINEX POLICY
10
Description
10.1 LIMITED WARRANTY / RETURN POLICY
CN5101US Insert plate w/ 1 U.S. AC connector
CN5102US Insert plate w/ 2 U.S. AC connectors
Please see the Altinex website at www.altinex.com
for details on warranty and return policy.
Blank insert plates, set of 5
Insert plate w/ 2 empty snap-in ports
Insert plate w/ 4 empty snap-in ports
CN5110RB
CNK-IP-105
CNK-IP-106
If your product is out of warranty and needs service,
contact the ALTINEX Sales Department for an RMA
(Return Material Authorization). Products returned
without an RMA number may experience a delay in
service. The service charges will be quoted to you
before the actual repairs are done.
Insert plate w/ a 15-pin HD female to
CNK-IP-107 male 6ft [1.8m] cable and 2 empty
snap-in ports
Insert plate w/ 1 empty D-Sub
CNK-IP-108 connector port for a DB9 or HD15
connector
10.2 CONTACT INFORMATION
ALTINEX, INC.
Insert plate w/ a 15-pin HD female to
male 6ft [1.8m] cable
CNK-IP-109
592 Apollo Street
accessories and cables.
Brea, CA 92821 USA
TEL: 714-990-2300
TROUBLESHOOTING GUIDE
9
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
The supplied Cable-Nook Jr.™ unit was carefully
tested and no problems were detected. However,
we would like to offer these recommendations:
E-MAIL: [email protected]
FAX: 714-990-3303
· Please make sure that the highest quality video,
audio, and any other cables or connectors are
used.
· Make sure that cables have not been damaged
or pinched. If there is damage to the unit then do
not use the Cable-Nook Jr.™ unit. Immediately
contact the ALTINEX Customer Service
Department to have the unit repaired.
· There are no adjustments necessary to operate
the Cable-Nook Jr.™, the unit will operate
successfully as long as the cables are attached
properly and other technical specifications are
followed.
7
|