Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #7581
Sit N Stand Plus
with Car Seat Snap N Go Attachment System
US PATENT #5,664,795
Instruction Manual
Convenience through innovation and thoughtful design
06.06
PARTS
Parent Tray
Front Wheels
Child Tray
Snap N Go Attachment
Bar
Rear Wheels
Foot Rest
Stroller
Front/Rear Canopies
ASSEMBLING
TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE
INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
ASSEMBLY
1. Remove stroller from box. The front wheels, rear wheels, child tray, and
canopies need to be installed prior to use.
Fig. 1.
2. To attach the front wheels, unfold stroller as described in the section
following. See figure 1. Lean the stroller backwards so that it rests on
the handle and rear frame tubes and the front wheel tubes are pointing
upward. Position the front wheel assembly at the front tube such that
the large hole in the swivel assembly will slide onto the front tube. Push
each front wheel assembly onto the front tube being careful that wheel
assembly locks onto the front leg. Pull on the wheel assembly to ensure
that it is securely attached to the stroller. Please see figure 2.
3. Lean the stroller forward to rest on the front wheels. To attach the rear
wheels, position the rear axle and wheel assembly such that the brake
levers are facing to the rear of the stroller. Press the rear wheel assembly
onto the rear frame tubes being careful that the push buttons on the
forward side of each rear tube engage the hole on the forward side of
each rear wheel housing. Pull on the rear wheel assembly to ensure that
it is securely attached to the stroller. Please see figure 3.
4. Ensure that the wheels are firmly locked into place. Do Not use the
stroller if the wheels are not locked into place, but rather contact our
customer service department immediately at (800) 328-7363, between
the hours of 8:00am and 4:30pm PCT, for assistance.
5. Snap footrest onto front legs of stroller just below the seat. Push
downward on the footrest until it locks onto the rivets protruding from
both sides of each leg and snaps onto the U-shaped frame cross member.
Please see figure 4.
Fig. 2.
Fig. 3.
Fig. 4.
Snap On
Push
Down
3
6. To attach the front child tray, push the tray onto the front frame tube,
lining up the tray between the protruding rivets. Push backward on the
latch until snapped into place. The protruding rivets on the outside of
the frame tube should be between the tray latch. Check that the tray is
securely latched in place. Please see figure 5 and 6.
Fig. 5.
7. To remove front child tray, pull outward on the latches and pull outward
on the tray. Please see figure 7. Please note that you may attach or
remove one end at a time.
Rivet
WARNING: The child’s tray is not a
restraint device: always secure your child with
the seat belt. DO NOT lift the stroller by the
child’s tray. Use care when attaching the child’s
tray on the stroller with a child in the stroller.
Fig. 6.
8. To attach the front canopy, line up the male fittings on the canopy with
the female fittings on the armrest and push both fittings downward until
snapped into place. Please see figure 8. Push forward on the front edge
of the canopy to open.
9. To attach the rear canopy line up the female fittings of the canopy with
the male fittings on the handle frame tube and push downward. Please
see figure 9.
Fig. 7.
10. To remove rear canopy reverse installation steps and pull up to remove.
Please see figure 9A.
11. To remove front canopy depress the plastic attachment and pull upward
to remove. Please see figure 9B.
Fig. 8.
Fig. 9.
Fig. 9A.
Fig. 9B.
4
WARNING: Avoid serious injury from
falling or sliding out. Always use the seat belt.
TO SECURE CHILD
Fig. 10.
TO SECURE FRONT/REAR SITTING CHILDREN
1 The shoulder straps of the 5-point harness has 2 attachment positions.
Select the loop position that places the shoulder strap level with, or below
the top of the child’s shoulder and feed the shoulder harness under the
correct loop. Please see figure 10.
Shoulder Strap
2. Carefully place the child in the stroller seat and bring the safety harness
around the child’s waist and over the shoulders. Place the crotch strap
and between the child’s legs. Insert the male end of each shoulder / waist
belt into the buckle on the crotch strap. Tighten the harness to be snug
around the child’s waist and over the child’s shoulders. Please see figure
11.
Waist
Strap
Squeeze
3. To release, apply pressure to both sides of each male clip until the clip
is released. This process requires a moderate amount of effort so as to
prevent an accidental release by your child. NOTE: Buckles may be hard
to release when 1st used.
Adjust for a
snug fit
Crotch Strap
Fig. 11.
TO SECURE REAR STANDING CHILD
1. The rear platform and jump seat are designed to accommodate a child
who is at least 2 1/2 years old, has good balance and coordination, and is
not over 40 inches tall. Position the child on the platform on the back of
the stroller. Be sure child is facing forward and hands are holding frame.
Secure the safety belt behind child and engage buckle. See figure 12.
2. Be sure that the child’s feet are fully on the platform at all times.
PLEASE NOTE: When using the rear SEAT you must put the STAND
FEATURE SAFETY BELT in the storage location located on the rear of
the seat. Please See Fig. 12A
Fig. 12.
WARNING: To avoid a possible
choking hazzard when using the rear seat, put
the STAND FEATURE SAFETY BELT in the
storage location on the rear of the seat.I
TO USE JUMP SEAT
Fig. 12A.
1. Have child sit on the jump seat facing backwards. Secure the seat belt,
which is attached to the back of the seat, around the child’s waist, and
buckle to the crotch strap. See figure 12B. Adjust the seat belt to be snug
around the child’s waist.
2. To release, apply pressure to both sides of the male clip until the clip
is released. This process requires a moderate amount of effort so as to
prevent an accidental release by your child.
3. Be sure that the child’s feet are fully on the platform at all times.
Fig. 12B.
5
TO RECLINE SEATS
SEATBACK POSITIONING
1. The front seat has a two position recline. To recline the seat, rotate the
recline bar and press backward on the seat back. Please see figure 13. To
place the seat in the upright position, press upward on the seat back while
rotating the recline bar.
2. The upright position should be used only for a child that is at least 6
months old. Note: Seat does not fully recline.
Fig. 13.
3. To recline the rear seat locate the plastic adjuster and squeeze the ends.
Loosen or tighten the strap to your desired recline position. Please see
figure 14.
TO REMOVE REAR SEAT
1. Remove the rear canopy. Locate the rear seat attachment positions.
Please see figure 15. Unhook the fabric from the tabs on the stroller
handle frame. Repeat for opposite side. Also un snap the footrest fabric
as shown in figure 15A. To completely remove rear seat fabric you
must unhook the D-Ring from the rear jump seat, and you must remove
the 2 D-Rings from the rear seat. Please See Figures 15B and 15C.
2. To remove the lower portion of the rear seat fabric, locate the two
attachment positions. Please See Figure 16. Unhook the fabric from
the tab on the lower frame tube, next release the front snap located on
the same lower frame tube.
Fig.14.
3. When you are not using the jump seat harness place it in the storage
location on the rear of the front seat. Please See Figure 16A.
Fig.15.
Fig.15.A
Fig.16.
Fig.15.B
Fig.16A.
Fig.15.C
6
BRAKES
WARNING: Always set brakes when
the stroller is not being pushed so that the
stroller will not roll away. Never leave stroller
unattended on a hill or incline as the stroller
Fig. 17.
Fig. 18.
may slide down the hill.
1. To engage brakes, apply light downward pressure to the brake lever located
on each rear wheel. The stroller may require slight forward or rearward
movement in order to line up the teeth on the brake with each wheel brake
cluster. See figure 17. Check that the stroller will not move and that the
brakes are properly applied. To release, gently lift up on the brake lever.
See figure 18.
CANOPIES
Fig. 19.
1. To open the canopies, push forward on the front frame of the canopies.
To close canopies, pull the front edge toward the rear of the stroller until
folded. Always fold the canopies prior to folding the stroller frame. Please
see figure 19.
2. The canopies will ratchet forward or back to block the sun. Pull forward
on the front canopy frame tube to move forward. Pull backward on the
rear frame tube to move back.
TO REMOVE FRONT CHILD TRAY
Fig. 20.
1. To remove front child tray, pull forward on the locking lever on the tray
arms to unlock. Please see figure 7. Please note that you may attach or
remove one end at a time. Also, the tray may be released on either side
and will swing away for easy access to your child.
Fold Button
TO FOLD STROLLER
Do Not allow children near stroller while folding.
1. Close the canopies as described in the Canopies section above. Ratchet
the front canopy all the way back. Please see figure 20.
Release Button
Fig. 21.
2. Unbuckle rear standing safety belt. Please see figure 12.
3. To fold the stroller slide the red fold latch safety button in the center of the
handle and squeeze the red handle while pushing forward on the handle.
Once the stroller begins to fold, release the red handle and pull upward on
the child tray until the stroller is folded. Please see figure 21.
4. Secure the stroller in the folded position by latching the fold latch, located
on the right side of the stroller handle, over the extended rivet on the
armrest. You may have to rotate the front wheels to fold the stroller
completely. Please see figure 22.
Fig. 22.
TO UNFOLD STROLLER
7
TO UNFOLD STROLLER
Do Not allow children near stroller while unfolding.
1. Release the folding latch, which is located on the right side. See figure
22.
2. Lift up on the stroller handle with both hands until the stroller frame is
erect and locked in the open position. The stroller has spring-loaded
latches on both sides of the frame. Test that both latches are fully engaged
prior to placing your child in the stroller.
WARNING: Avoid serious injury from
falling, Do Not use the Snap N Go bar if it is not
securely locked onto both sides of the stroller.
TO ATTACH AN INFANT CAR SEAT
Fig. 23.
1. Recline the front seat back. Remove the child tray.
2. Slide snap n go attachment bar into the female slots located on the
frame tube. Make sure the snap n go attachment bar locks in place
before attaching the car seat. See figure 23.
3. Place car seat onto front bar. See figure 24. NOTE: Most brands
of infant car seats will lock onto the front bar, and some brands
may simply rest on the front bar, FOR SAFE OPERATION, IT
IS VERY IMPORTANT THAT THE CAR SEAT STRAP IS
ALWAYS TIGHTLY FASTENED AROUND THE CAR SEAT.
4. Strap the safety belt over the car seat and through the seat belt slots
on your car seat, connect the buckles together. Tighten the strap so
the car seat fits snug and can't move. See figure 24. Check that the
car seat is secure before using the stroller.
Fig. 24.
STOP
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE
CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363 BETWEEN
THE HOURS OF 8:00AM AND 4:30PM PACIFIC COAST TIME FOR ASSISTANCE.
8
|