SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of electrical shock, do not remove
the cover (or back). No user serviceable parts inside;
refer servicing to qualified personnel.
WARNING: To reduce the risk of fire or electrical shock, do not
expose this appliance to rain or moisture.
E
This symbol, wherever it appears,
alerts you to the presence of
uninsulated dangerous voltage inside
the enclosure - voltage that may be
sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts
you to important operating and
maintenance instructions in the
accompanying literature. Read the
manual.
DETAILED SAFETY INSTRUCTIONS:
All the safety and operation instructions should be read before the appliance is operated.
Retain Instructions:
The safety and operating instructions should be retained for future reference.
Heed Warnings:
All warnings on the appliance and in the operating instructions should be adhered to.
Follow instructions:
All operation and user instructions should be followed.
Water and Moisture:
The appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool etc.).
Ventilation:
The appliance should be situated so that its location or position does not interfere with its proper ventilaton.
For example, the appliance should not be situated on a bed, sofa rug, or similar surface that may block the
ventilation openings: or placed in a built-in installation, such as a bookcase or cabinet that may impede the
flow of air through the ventilation openings.
Heat:
The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
Power Source:
The appliance should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
Grounding or Polarization:
Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.
Power-Cord Protection:
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords and plugs, convenience receptacles and the point
where they exit from the appliance.
Cleaning:
The appliance should be cleaned only as recommended by the manufacturer.
Non-use Periods:
The power cord of the appliance should be unplugged from the outlet when left unused for a long period of
time.
Object and Liquid Entry:
Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.
Damage Requiring Service:
The appliance should be serviced by qualified service personnel when:
- The power supply cord or the plug has been damaged; or
- Objects have fallen, or liquid has been spilled into the appliance; or
- The appliance has been exposed to rain; or
- The appliance does not appear to operate normally or exhibits a marked change in performance; or
- The appliance has been dropped, or the enclosure damaged.
Servicing:
The user should not attempt to service the appliance beyond that which is described in the Operating Instructions.
All other servicing should be referred to qualified service personnel.
3
FOREWORD
Dear Customer,
Welcome to the team of TRUTH B2031 users and thank you very much for expressing your confidence in
BEHRINGER products by purchasing this studio monitor.
It is one of my most pleasant tasks to write this letter to you, because it is the culmination of many months of
hard work delivered by our engineering team to reach a very ambitious goal: making an outstanding reference
studio monitor that will become a standard tool. The task to design the TRUTH B2031 certainly meant a great
deal of responsibility, which we assumed by focusing on you, the discerning user and musician. It also meant
a lot of work and night shifts to accomplish this goal. But it was fun, too. Developing a product usually brings
a lot of people together, and what a great feeling it is when everybody who participated in such a project can
be proud of what we’ve achieved.
It is our philosophy to share our joy with you, because you are the most important member of the BEHRINGER
family. With your highly competent suggestions for new products you’ve greatly contributed to shaping our
company and making it successful. In return, we guarantee you uncompromising quality (manufactured
under ISO9000 certified management system) as well as excellent technical and audio properties at an
extremely affordable price. All of this will enable you to fully unfold your creativity without being hampered by
budget constraints.
We are often asked how we are able to possible to produce such high-grade devices at such unbelievably low
prices. The answer is quite simple: it’s you, our customers! Many satisfied customers means large sales
volumes enabling us to get better conditions of purchase for components, etc. Isn’t it only fair to pass this
benefit back to you? Because we know that your success is our success, too!
I would like to thank all people whose help on “Project TRUTH B2031“ has made it all possible. Everybody has
made very personal contributions, starting from the designers of the unit via the many staff members in our
company to you, the user of BEHRINGER products.
My friends, it’s been worth the trouble!
Thank you very much,
Uli Behringer
4
TRUTH
2-way active high-resolution studio monitor
s Ultra-linear frequency response from 50 Hz to 21 kHz
E
s Two built-in high power amps with 150/75 Watts and enormous power reserves
s Extremely high-resolution tweeter with ferrofluid-cooled titanium dome
s Long-throw 8.75" woofer with special polycarbonate diaphragm and sturdy cast aluminum chassis
s Controlled dispersion pattern through phase-optimized wave guide system
s Extremely large "sweet spot" through vertically/horizontally balanced dispersion characteristics
s Active frequency crossover with 4th order Linkwitz-Riley filters
s Flexible adaptation to room acoustics, incl. subwoofer operation
s Overload protection through separately controlled limiter for low- and high-frequency ranges
s Automatic standby switching
s Electromagnetic shielding for minimum interference
s Delivery of "matched pairs". Measurement protocol included
s Low-vibration E1 MDF cabinet
s Servo-balanced inputs on XLR and TRS connectors
s Manufactured under ISO9000 certified Management System
5
TABLE OF CONTENT
1. INTRODUCTION ......................................................................................................................7
1.1 The concept.................................................................................................................................... 7
1.2 Before you start .............................................................................................................................. 7
1.3 Control elements ............................................................................................................................. 8
2. APPLICATIONS .....................................................................................................................10
2.1 Connection ................................................................................................................................... 10
2.2 Level setting .................................................................................................................................. 10
2.3 Recommended setup .....................................................................................................................11
2.4 Adapting the TRUTH to the room acoustics ................................................................................... 12
3. INSTALLATION ......................................................................................................................14
3.1 Speaker setup ............................................................................................................................... 14
3.2 Mains voltage ................................................................................................................................ 14
3.3. Audio connections ........................................................................................................................ 14
4. SPECIFICATIONS ..................................................................................................................16
5. WARRANTY ...........................................................................................................................17
6
1. INTRODUCTION
Congratulations! With our new BEHRINGER TRUTH B2031 you have purchased one of the best high-resolution
active studio monitors available. It is a tool that reproduces your program material with highest fidelity and
balance, positioning sound sources accurately on the stereo basis.
We recommend that you experiment with your B2031 away from the pressures of a recording session, in
order to get a feel for it. It will be a good idea to listen to your favorite CD's over the TRUTH, so that you can
get an impression of the neutral sound this speaker produces - which might be somewhat unusual at first!
E
1.1 The concept
The B2031 is equipped with two separate power amps for the woofer and tweeter ranges. With 150 and 75
Watts respectively, these amps have lots of power reserves. In the low-frequency range we used an 8.75"
soft-suspension speaker with a sturdy cast aluminum chassis. Its effective operating range is expanded
downwards by a special bass reflex system. The innovative shape of the reflex tunnel reduces airflow noise
even at highest sound pressure levels. In the high-frequency range a titanium-dome tweeter ensures an
extremely fine signal resolution. Sophisticated circuitry is used to protect both chassis and amplifiers against
overloading. Both speakers are electromagnetically shielded, so that you can operate the TRUTH in close
proximity to your computer monitor or TV set. The individual frequency ranges driving the speakers are
derived by means of an active crossover network, which allows for the precise separation of frequency bands
and the perfect adaptation of two speakers to each other. Rear-mount switches enable you to configure the
crossover networks, so as to adapt the speakers to specific room acoustics. More on this later.
High-quality components and design
The philosophy behind BEHRINGER products guarantees a no-compromise circuit design and employs the
best choice of components. The operational amplifiers 4580 which are used in the TRUTH B2031, are
exceptional. They boast extreme linearity and very low distortion characteristics. To complement this design
the choice of components includes high-tolerance resistors and capacitors, high-grade switches and several
other stringently selected elements. Additionally, the TRUTH is manufactured in compliance with a ISO9000
certified management system.
1.2 Before you start
Your TRUTH was carefully packed in the factory and the packaging is designed to protect the unit from rough
handling. Nevertheless, we recommend that you carefully examine the carton and its contents for any signs of
physical damage, which may have occurred during transit.
+
If the unit is damaged, please do NOT return it to BEHRINGER, but notify your dealer and the
shipping company immediately, otherwise claims for damage or replacement may not be granted.
Shipping claims must be made by the consignee.
The TRUTH must be placed on a flat and stable surface. Be sure that there is enough air space around the
unit for cooling and please do not place the TRUTH on high-temperature devices such as power amps, etc. to
avoid overheating.
+
Before you connect the TRUTH to the mains, please make sure that your local voltage matches
the voltage required by the unit!
Please use the enclosed power cord to connect the unit to the mains. The cord complies with all applicable
safety standards.
+
Please note that all units must be grounded properly. For your own safety, you should never
remove any ground connectors from electrical devices or power cords or render them
inoperative.
Further information can be found in chapter 3 "INSTALLATION".
1. INTRODUCTION
7
1.3 Control elements
The control elements described in the following are the same on both speakers.
Fig. 1.1: Front panel display elements
1
2
ON. This LED lights up as soon as you switch on the speaker.
LIMIT. Lights up as soon as one of the built-in protections is activated.
Fig. 1.2: Rear panel input connectors
All connectors of the TRUTH face downwards, so as to allow you to place the speaker as closely to a wall as
possible.
3
4
5
INPUT. This balanced TRS connector is used to connect the speaker to a signal source.
INPUT. This XLR connector is used to connect the speaker to a balanced signal source.
Use the POWER switch to put the TRUTH into operation.
+
The TRUTH should be the last device in the signal chain to be switched on and the first to be
switched off.
6
FUSE holder/VOLTAGE selector and MAINS connector. Please make sure that your local voltage
matches the voltage indicated on the unit, before you attempt to connect and operate the TRUTH.
Blown fuses may only be replaced by fuses of the same type and rating. Use the enclosed power cord
to connect the unit to the mains. Please note the instructions given in chapter 3 “INSTALLATION”.
Fig. 1.3: The serial number of your TRUTH
1. INTRODUCTION
8
7
SERIAL NUMBER. Please take the time to have the warranty card filled out completely by your specialized
dealer, and return it within 14 days after the date of purchase, so as to be entitled to benefit from our
extended warranty.
E
Fig. 1.4: Rear panel control elements
INPUT TRIM. Use this control to adapt the TRUTH's input sensitivity to the signal source.
POWER MODE. This switch allows you to toggle between "ON", "OFF" and "AUTO" power-up modes.
MUTE LOW. Disables the woofer for servicing and maintenance.
MUTE HIGH. Disables the tweeter for servicing and maintenance.
Fig. 1.5: Rear panel switches
LOW FREQUENCY. With this switch you can adapt the woofer range to a subwoofer system or
emulate the sound characteristics of small speaker systems.
ROOM COMPENSATION. For maximum flexibility the TRUTH features a switch that adjusts the speaker
depending on its setup position.
HIGH FREQUENCY. This switch adapts the speaker's frequency response to the damping
characteristics of the control room.
1. INTRODUCTION
9
2. APPLICATIONS
2.1 Connection
Use the enclosed power cord to connect the B2031 to the mains. To avoid ground loops, both speakers and
the mixing console should be fed from the same outlet. For your convenience, the TRUTH features an
automatic power-up system which activates the B2031 as soon as a signal is present on its input, and
deactivates the speaker after signal pauses of more than five minutes.
Function: The switch for the automatic power-up system
speaker is completely switched off and cannot be activated with switch
has three positions. When set to OFF, the
5
. Position AUTO allows the
automatic operation as mentioned above. In position ON, the B2031 is activated all the time and can be
5
switched off only with switch
.
5
+
Be sure to switch the TRUTH off with switch
during longer pauses.
Now connect both speakers to your console by means of commercial XLR or TRS cables. Since the B2031 is
an active speaker system, instead of conventional speaker cables you will need normal TRS or XLR cables.
Connect the TRUTH to the Control Room outputs of your console, so as to be able to control the monitoring
volume independently of the Main Mix level. If your console does not have such outputs, you can also use the
Aux, Tape or Main outputs. However, in this case the speaker volume cannot be set independently of the Main
Mix level, i.e. you must adjust the monitoring volume on the TRUTH. Please consult the operating instructions
accompanying your console to find out whether it has balanced or unbalanced outputs. Connect these
3
4
outputs to the TRS
or XLR
input. If possible use the balanced connectors, so as to avoid interference
and hum. It won't help, however, to connect unbalanced outputs with balanced inputs. The benefits mentioned
above will apply only when both inputs and outputs are of the balanced type. If all else fails, you can still
connect the TRUTH to the headphones output of your console.
+
Be sure to mute the signal sources before you put the B2031 into operation.
5
Once the TRUTH has been connected as described above, you can activate the speaker with switch
.
2.2 Level setting
When the TRUTH has been connected properly and switched on, you can now turn up the console output that
feeds the B2031. Provided you have a signal source connected, you now hear the audio material as it is
played back by the TRUTH. The INPUT TRIM control
on the rear panel is set to 0 dB ex-factory, i.e. unity
gain, which is okay when you feed the TRUTH from a pro-level console. In this case, the B2031 automatically
operates at maximum level, provided that your console has been set up correctly and its output is set to 0 dB.
2
The LIMIT LED
helps you control the level. It lights up as soon as overloading causes one of the internal
protections to respond. The TRUTH doesn't get damaged when the LIMIT LED lights up with occasional signal
peaks. However, please make sure that it won't light up all the time, because sooner or later this will activate
the thermal protection system and temporarily mute the built-in amplifiers, to warn you that you are driving the
B2031 too hard. If so, you can reduce levels either on your console or using the INPUT TRIM control
.
If the outputs on your console don't provide studio-level signals, you can turn up the INPUT TRIM control. If
you connect the TRUTH to the preamp output of your stereo system, it may also be necessary to raise the
level on the TRUTH itself. To build up a rudimentary stereo system, you can directly connect the outputs of a
CD player (if they can be controlled in volume) to the B2031's inputs, and use the CD player to adjust the
volume.
+
The TRUTH is capable of producing high volume levels. You should mix your recordings at
moderate levels, so as to avoid listening fatigue and hearing impairment.
10
2. APPLICATIONS
2.3 Recommended setup
Even though the B2031 is an excellent active speaker, it needs to be set up with great care, because even the
built-in room adaptation facility cannot make up for poor positioning of the speaker. Please try to heed the
following suggestions. As the TRUTH will give you an even better sound and higher resolution, it will be worth
the trouble.
Place the TRUTH on a flat and stable surface, if possible use a dedicated speaker stand. In this way, the
speaker is acoustically decoupled and won't induce vibrations in nearby objects, which would affect the bass
response. If you cannot use a stand, put the B2031 on spikes or damping foam material. Another aspect is
the distance between speaker and wall: keep the speaker away from the wall, as this would emphasize the
bass response, particularly in corners, where two walls form an angle.
E
The BEHRINGER TRUTH B2031 is a so-called near-field monitor, which means that the impact of the room
acoustics on the sound will be reduced considerably owing to the short distance between speaker and
listener.
Fig. 2.1: Incorrect speaker setup
This illustration shows how you shouldn't do it: you can clearly see that a portion of the sound bounces back
from the walls before it reaches the listener's ears. Thus, direct and reflected sound waves overlap which
results in a coloration of the sound.
2. APPLICATIONS
11
Fig. 2.2: Correct speaker setup
This effect can be reduced by turning the speakers towards the listener. To make reflections from ceiling or
floor less likely, the tweeters should be on the same height as your ears. Please note that the TRUTH should
be operated vertically. Where this is impossible, place it horizontally as shown in the illustration (i.e. woofers
closer to each other), to allow for an improved stereo image.
Fig. 2.3: TRUTH setup horizontally
In addition to the setup position, the room characteristics also have quite an impact on the sound the TRUTH
produces. Although control room designers have calculated some ideal room sizes, we assume that you are
not willing to rebuild your entire studio, just to be able to set up a pair of speakers. Nevertheless, you should
consider the following tips:
The room acoustics should neither be too reflective nor too dull (i.e. neither bathroom nor anechoic chamber).
You can alter the room acoustics easily by installing or removing carpets, curtains or furniture. Fabric
covering on the wall opposite the speakers might be a good idea if the room is too reflective. The next chapter
describes how to adapt the TRUTH to the room acoustics, once it has been set up properly.
2.4 Adapting the TRUTH to the room acoustics
This chapter describes how you can use the switches on the rear of the B2031 to adapt the speaker to the
acoustics of your control room. However, you should try to improve a potentially impaired sound by optimizing
the speaker setup beforehand.
12
2. APPLICATIONS
E
Fig. 2.4: Rear wall legending
If you are still having problems, you could try the following: The ROOM COMPENSATION switch
allows
you to lower the bass range, depending on the speaker position. Ex-factory, the switch is set to a neutral
position. If you've set up the TRUTH close to the wall or in a corner, try reducing the low-frequency level in
steps of 2 dB. Since every room and speaker setup are unique in their acoustic properties, we cannot
provide more specific information here. The same applies to the HIGH FREQUENCY switch
, which
determines the tweeter level (between +2 dB and -4 dB). Here too, the best setting depends on the room
acoustics. If you have an additional subwoofer installed, you should match the TRUTH's lower cutoff frequency
to that of the subwoofer, using the LOW FREQUENCY switch
in the subwoofer documentation, it must be determined by ear.
. Unless the appropriate frequency is given
As a general rule, you should set up and adjust the TRUTH with great care. Above all, you should take your
time: unlike hi-fi speakers, the B2031 is tuned to produce a neutral sound, which can be confusing when you
are working for the first time with such a high-quality speaker. Don't try to adjust the TRUTH with its rear-wall
switches to produce a "bombastic" sound that impresses you or other listeners. To get a feeling for the
TRUTH's sound, you should listen to as many records as possible that were produced in other studios. We
also recommend that you listen to your own recordings over as many other systems as possible, for example,
your car system. If you find that your mixes are somewhat "dull" in their overall sound, the reason might be
too much treble power from your TRUTH. On the other hand, if you set the bass level to high, you will find that
your mixes lack bass power. Tuning a speaker can take several days' time, so once again: take your time!
It might be necessary to insert an equalizer between console and speaker, in particular, if you prefer extreme
setups or sound images. The BEHRINGER ULTRA-CURVE PRO DSP8024 has proven its usefulness in
practice, as it is not only a simple equalizer but also includes analyzer circuitry. You can use our measuring
microphone ECM8000 to automatically adapt the TRUTH to your room or modify its frequency response.
2. APPLICATIONS
13
3. INSTALLATION
Your TRUTH was carefully packed in the factory and the packaging is designed to protect the unit from rough
handling. Nevertheless, we recommend that you carefully examine the carton and its contents for any signs of
physical damage, which may have occurred in transit.
+
If the unit is damaged, please do NOT return it to BEHRINGER, but notify your dealer and the
shipping company immediately, otherwise claims for damage or replacement may not be granted.
Shipping claims must be made by the consignee.
3.1 Speaker setup
The BEHRINGER TRUTH must be placed on a flat and stable surface.
+
Be sure that there is enough air space around the unit for cooling and please do not place the
TRUTH on high-temperature devices such as power amps, etc. to avoid overheating.
3.2 Mains voltage
Before you connect the TRUTH to the mains, please make sure that your local voltage matches the voltage
required by the unit! The fuse holder on the female mains connector has 3 triangular markers, with two of
these triangles opposing each other. The TRUTH is set to the operating voltage printed next to these markers,
and can be set to another voltage by turning the fuse holder by 180°. CAUTION: this instruction does not
apply to export models exclusively designed, e.g. for 115 V operation!
Please use the enclosed power cord to connect the unit to the mains. The cord complies with all applicable
safety standards.
+
Please note that all units must be grounded properly. For your own safety, you should never
remove any ground connectors from electrical devices or power cords or render them
inoperative.
3.3. Audio connections
The BEHRINGER TRUTH has balanced XLR and unbalanced TRS input connectors. If possible, connect the
unit to other devices in a balanced configuration to allow for maximum interference immunity.
14
3. INSTALLATION
Output
Cable
Input
Ground
Positive
Negative
Pin 1
2
1
1
2
Shield
(+) Signal + Hum
(-) Signal + Hum
Pin 2 = (+) Signal
Pin 3 = (-) Signal
(+)Hum + Signal
(-)Hum + Signal
3
3
E
2 x Signal
= Signal + 6 dB
RFI and Hum
Fig. 3.1: Compensation of interference with balanced connections
Unbalanced use of
Balanced use of
mono 1/4" jack plugs
stereo 1/4" jack plugs
Tip =
Signal
Tip =
hot (+ve)
Ring =
cold (-ve)
Sleeve =
Ground / Shield
Sleeve =
Ground / Shield
Tip
Tip
Ring
Sleeve
Sleeve
Strain relief clamp
Strain relief clamp
For connection of balanced and
unbalanced plugs, ring and sleeve have
to be bridged at the stereo plug.
Balanced use with XLR connectors
2
1
1
2
1 = Ground / Shield
2 = hot (+ve)
3 = cold (-ve)
3
3
Input
Output
For unbalanced use pin 1 and pin 3 have to be bridged
Fig. 3.2: Different plug types
3. INSTALLATION
15
4. SPECIFICATIONS
Audio inputs
XLR
1/4" jack
Impedance
Max. input level
servo-balanced input
servo-balanced input
20 kOhms
+22 dBu
Loudspeaker
Tweeter
25 mm ferrofluid-cooled dome
Woofer
22 cm (8.75") polycarbonate diaphragm
Amplifiers
Low frequency
max. 150 watts
High frequency
max. 75 watts
Noise (SPL @ 10 cm)
<10 dBA @ 1 m (each)
Crossover
Type
Crossover frequency
active, 4th order Linkwitz-Riley filter
2 kHz
System specifications
Bandwidth
50 Hz to 21 kHz
Sound pressure level
max. 116 dB SPL @ 1 m (pair)
Power supply
Mains voltages
U.S.A./Canada
120 V ~, 60 Hz
U.K./Australia
240 V ~, 50 Hz
Europe
230 V ~, 50 Hz
general export model
100 - 120 V ~ : T 5.0 A H
200 - 240 V ~ : T 2.5 A H
100 - 120 V ~, 200 - 240 V ~, 50 - 60 Hz
Fuse
Power consumption
Mains connection
210 watts, standby 27 watts
standard IEC receptacle
Physical
Dimensions (H * W * D)
Net weight
400 mm * 250 mm * 290 mm
approx. 15 kg (each)
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from
time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.
16
4. SPECIFICATIONS
5. WARRANTY
§ 1 WARRANTY CARD
To be protected by this warranty, the buyer must complete and
return the enclosed warranty card (signed/stamped by retail dealer)
within 14 days of the date of purchase to BEHRINGER
INTERNATIONAL (address see § 3). Failure to return the card in
due time (date as per postmark) will void any extended warranty
claims.
workmanship. The warranty does not cover any such
modification/adaptation, irrespective of whether it was carried
out properly or not. Under the terms of this warranty, BEHRINGER
INTERNATIONAL shall not be held responsible for any cost
resulting from such a modification/adaptation.
3. Free inspections, maintenance/repair work and replacement
of parts are expressly excluded from this warranty, in particular
if caused by inappropriate use. Likewise, the warranty does not
cover defects of expendable parts caused by normal wear of
the product. Expendable parts are typically faders,
potentiometers, switches and similar components.
§ 2 WARRANTY
E
1. BEHRINGER INTERNATIONAL warrants the mechanical and
electronic components of this product to be free of defects in material
and workmanship for a period of one (1) year from the original date
of purchase, in accordance with the warranty regulations described
below. If any defects occur within the specified warranty period that
are not caused by normal wear or inappropriate use, BEHRINGER
INTERNATIONAL shall, at its sole discretion, either repair or replace
the product.
4. Damages/defects caused by the following conditions are not
covered by this warranty:
s
misuse, neglect or failure to operate the unit in compliance
with the instructions given in the user or service manuals.
2. If the warranty claim proves to be justified, the product will be
returned freight prepaid by BEHRINGER INTERNATIONAL within
Germany. Outside of Germany, the product will be returned at the
buyer’s expense.
s
connection or operation of the unit in any way that does not
comply with the technical or safety regulations applicable in
the country where the product is used.
s
damages/defects that are caused by force majeure or by any
other condition beyond the control of BEHRINGER
INTERNATIONAL.
3. Warranty claims other than those indicated above are expressly
excluded.
§ 3 RETURN AUTHORIZATION NUMBER
5. Any repair carried out by unauthorized personnel will void the
warranty.
1. To obtain warranty service, the buyer must call BEHRINGER
INTERNATIONAL during normal business hours BEFORE returning
the product (Tel.: +49 (0) 21 54 / 92 06 66). All inquiries must be
accompanied by a description of the problem. BEHRINGER
INTERNATIONAL will then issue a return authorization number.
6. Products which do not meet the terms of this warranty will be
repaired exclusively at the buyer’s expense. BEHRINGER
INTERNATIONAL will inform the buyer of any such circumstance. If
the buyer fails to submit a written repair order within 4 weeks after
notification, BEHRINGER INTERNATIONAL will return the unit
C.O.D. with a separate invoice for freight and packing. Such cost
will also be invoiced separately when the buyer has sent in a written
repair order.
2. The product must be returned in its original shipping carton,
together with the return authorization number, to the following
address:
BEHRINGER INTERNATIONAL GmbH
Service Department
§ 5 WARRANTY TRANSFERABILITY
Hanns-Martin-Schleyer-Str. 36-38
47877 Willich-Münchheide
Germany
This warranty is extended exclusively to the original buyer (customer
of retail dealer) and is not transferable to anyone who may
subsequently purchase this product. No other person (retail dealer,
etc.) shall be entitled to give any warranty promise on behalf of
BEHRINGER INTERNATIONAL.
3. Shipments without freight prepaid will not be accepted.
§ 4 WARRANTY REGULATIONS
§ 6 CLAIM FOR DAMAGES
1. Warranty services will be furnished only if the product is
accompanied by an original retail dealer’s invoice. Any product
deemed eligible for repair or replacement by BEHRINGER
INTERNATIONAL under the terms of this warranty will be repaired
or replaced within 30 days of receipt of the product at BEHRINGER
INTERNATIONAL.
Failure of BEHRINGER INTERNATIONAL to provide proper warranty
service shall not entitle the buyer to claim (consequential) damages.
In no event shall the liability of BEHRINGER INTERNATIONAL
exceed the invoiced value of the product.
§ 7 OTHER WARRANTY RIGHTS
2. If the product needs to be modified or adapted in order to comply
with applicable technical or safety standards on a national or local
level, in any country which is not the country for which the product
was originally developed and manufactured, this modification/
adaptation shall not be considered a defect in materials or
This warranty does not exclude or limit the buyer’s statutory rights
provided by national law, in particular, any such rights against the
seller that arise from a legally effective purchase contract.
The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any
purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER and ULTRA-CURVE are registered trademarks.
ALL RIGHTS RESERVED © 2000 BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36 - 38, 47877 Willich-Münchheide II, Germany
Tel. +49 (0) 21 54 / 92 06 - 0, Fax +49 (0) 21 54 / 92 06 - 30
5. WARRANTY
17
|