User’s manual
Version 1.1 June 2006
ULTRABASS BX4410/BX4410A
TABLE OF CONTENTS
FOREWORD
Dear Customer,
1. INTRODUCTION ......................................................... 4
Welcome to the team of
ULTRABASS users and
thank you very much for
expressing your confi-
dence in BEHRINGER
products by purchasing
the BEHRINGER BX4410/
BX4410A.
1.1 The design concept ........................................................ 4
1.1.1 Patented Dynamizer technology .......................... 4
1.2 Before you get started ................................................... 4
1.2.1 Shipment ............................................................... 4
1.2.2 Initial operation...................................................... 4
1.2.3 Online registration ................................................ 5
It is one of my most
pleasant tasks to write
this letter to you,
2. CONTROL ELEMENTS ............................................... 5
2.1 Front panel ...................................................................... 5
2.2 Rear panel ...................................................................... 6
because it is the cul-
mination of many months
of hard work delivered
by our engineering team
to reach a very ambitious
goal: to present you with
an outstanding bass
workstation that gives
3. WIRING EXAMPLES ................................................... 6
3.1 Standard setup comprising footswitch
and external loudspeaker .............................................. 6
3.2 Expanded setup with tuner and
connection to a mixing console ...................................... 7
3.3 Connecting several loudspeakers ................................. 7
3.3.1 Calculating the total impedance when
you maximum flexibility and performance with its unique sound
character and broad range of functions.
connecting several loudspeakers ....................... 7
3.4 Connection of a multi-effects processor....................... 7
3.5 Setup for master/slave operation .................................. 7
3.5.1 ULTRABASS BX4410/BX4410A as master ......... 7
3.5.2 ULTRABASS BX4410/BX4410A as slave
controlled by an external amp/preamp ................ 7
The task to design the new ULTRABASS certainly meant a
great deal of responsibility, which we assumed by focusing on
you, the discerning user and musician. It also meant a lot of work
and night shifts to accomplish this goal. But it was fun, too.
Developing a product usually brings a lot of people together, and
what a great feeling it is when everybody who participated in
such a project can be proud of what we’ve achieved.
4. SHAPE FUNCTION ..................................................... 8
5. ULTRABASS FUNCTION ............................................ 8
6. INSTALLATION ........................................................... 8
It is our philosophy to share our joy with you, because you are
the most important member of the BEHRINGER team. With your
highly competent suggestions for new products you’ve greatly
contributed to shaping our company and making it successful. In
return, we guarantee you uncompromising quality as well as
excellent technical and audio properties at an extremely
favorable price. All of this will enable you to fully unfold your
creativity without being hampered by budget constraints.
6.1 Mains connection ........................................................... 8
6.2 Audio connections ......................................................... 8
6.2.1 Loudspeaker connections ................................... 9
We are often asked how we can produce such high-grade
devices at such unbelievably low prices. The answer is quite
simple: it’s you, our customers! Many satisfied customers means
large sales volumes enabling us to get better conditions of
purchase for components, etc. Isn’t it only fair to pass this benefit
back to you? Because we know that your success is our
success, too!
7. SPECIFICATIONS ....................................................... 9
8. WARRANTY ..............................................................10
I would like to thank all people whose help on “Project
ULTRABASS” has made it all possible. Everybody has made
very personal contributions, starting from the designers of the
unit to the many staff members in our company and finally to you,
the users of BEHRINGER products.
My friends, it’s been worth the trouble!
Thank you very much,
Uli Behringer
WARNING!
+
It should be pointed out that extreme output
volumes may damage your hearing and/or your
headphones. Turn down all LEVEL controls before
you switch on the unit. Always set the volume at an
appropriate level.
3
ULTRABASS BX4410/BX4410A
1.1.1 Patented Dynamizer technology
1. INTRODUCTION
When it comes to amplifying the signals delivered by electric
instruments, you’ve got to separate the wheat from the chaff.
Unlike mixed or mastered signals, electric instruments usually
deliver extremely high signal peaks which, when raised in gain,
produce nasty distortion. How an amplifier responds to these
signal peaks can therefore be seen as one of its most essential
quality features.
Congratulations! With the BX4410/BX4410A you have acquired
a pro-level amplifier from our BX bass amplifier series. This
revolutionary bass amplifier has many of the features of our
successful BX1200. Our top goal when designing the BX4410/
BX4410A was to set new standards. In fact, the BX4410/
BX4410A is a bass amp that gives you a full set of features plus
a comprehensive range of connection and expansion options.
With this amp you’ll certainly rattle the planet!
Many manufacturers use limiters preceding the power stage
to limit dynamic signal peaks. However, the problem is the preamp,
which is why we’ve equipped the BX4410/BX4410A with our
unique Dynamizer preamp circuitry that gives you a lively and
punchy sound with signal peaks—even if the amp reaches its
power limits. Extreme signal peaks are limited effectively while
the average level and hence the power of the overall signal is
raised. The sound gets more vivid and powerful in character,
without any unmusical distortion. With its limiter in the power
stage it is virtually impossible to overdrive the ULTRABASS
BX4410/BX4410A.
BEHRINGER is an audio engineering company that has been
successfully developing products for studio and live applications
for many years now. Our range of products includes
microphones and a variety of 19" devices (compressors,
enhancers, noise gates, tube processors, headphone amps,
digital effects devices, DI boxes, etc.) as well as monitoring and
P.A. speakers plus professional live and recording consoles.
You will find all of our technical know-how combined in your
BX4410/BX4410A.
Flexibility has become a particularly important factor in the
music business over the past few years. Modern bass players
need to offer a broad range of sounds, but should still be able to
play in different kinds of applications at short notice: home
recording, studio, live concerts. For this reason, it has always
been our prime concern to give you a bass amplifier that offers
a complete set of useful functions, but can still be operated
intuitively and quickly.
1.2 Before you get started
1.2.1 Shipment
Your BX4410/BX4410A was carefully packed at the factory
and the packaging is designed to protect the unit from rough
handling. Nevertheless, we recommend that you carefully
examine the packaging and its contents for any signs of physical
damage that may have occurred during transit.
Additionally, the world of electric bass playing has changed:
new basses, with five or six strings, are being launched all the
time, there are effects devices and the desire to create one’s
own “unique” sound—which can only be achieved with
innovative amplifiers. Our unique ULTRABASS BX4410/BX4410A
gives you pioneering sounds and power galore.
+
If the unit is damaged, please do not return it to
BEHRINGER, but notify your dealer and the shipping
company immediately, otherwise claims for damage
or replacement may not be granted. Shipping claims
must be made by the consignee.
We have expanded our BX Series with this amplifier to give
you all the freedom you need when expanding your set-up. No
matter which speakers or cabinets you prefer—with its superb
sound, your BX4410/BX4410A will bring some life into your
speaker.
1.2.2 Initial operation
Be sure that there is enough space around the unit for cooling
and please do not place the ULTRABASS on high temperature
devices such as radiators etc. to avoid overheating.
As technology advances, you’ve got to keep track of the latest
technological breakthroughs to avoid falling by the wayside.
Which is what we did, by continuously improving this bass
amplifier and including many of your valuable suggestions.
+
Before you connect your ULTRABASS to the mains,
please make sure that your local voltage matches
the voltage required by the unit:
Experience a new-generation bass amp with fascinating
features:
The fuse holder on the female mains connector has 3 triangular
markings, with two of these triangles opposing each other. The
ULTRABASS is set to the operating voltage printed next to these
markers and can be set to another voltage by turning the fuse
holder by 180°. CAUTION: This instruction does not apply
to export models exclusively designed e.g. for 120 V
operation!
s
s
s
s
4 original BUGERA™ 10" Hard Attack aluminum-cone speakers
and switchable 1" custom-made horn tweeter (BX4410A).
4 original BUGERA™ 10" special high-impact cone speakers
and switchable 1" custom-made horn tweeter (BX4410).
Astounding sound diversity through SHAPE filter and
ULTRABASS sub-harmonics processor.
+
If you set the unit to a different mains voltage, be
sure to use a fuse of the correct type and rating.
Please refer to the “SPECIFICATIONS” for details.
Unbelievable punch through innovative Dynamizer preamp
technology.
s
s
s
More gain, but no distortion through built-in limiter.
+
Blown fuses must be replaced by fuses of the same
type
and
rating!
Please
refer
to
the
Optimum level metering through clearly visible VU meter.
“SPECIFICATIONS” for details.
A 5-band EQ with additional “Deep” and “Bright” functions
meets all requirements in terms of tone-shaping.
The mains connection of the BX4410/BX4410A is made by
using the enclosed mains cable and a standard IEC receptacle. It
meets all of the international safety certification requirements.
s
Plenty of power plus a built-in DI output—even on big stages
you’ll cut a fine figure with your BX4410/BX4410A.
+
Please make sure that all units have a proper
ground connection. For your own safety, never
remove or disable the ground conductor from the
unit or of the AC power cord.
1.1 The design concept
This absolutely low-noise and indestructible bass amp
represents the current state of the art.
The rugged enclosure of your ULTRABASS ensures that the
unit will withstand rough handling on the road over many years.
4
1. INTRODUCTION
ULTRABASS BX4410/BX4410A
1.2.3 Online registration
Please do remember to register your new BEHRINGER
equipment right after your purchase by visiting
kindly read the terms and conditions of our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to
have it repaired as quickly as possible. To arrange for warranty
service, please contact the retailer from whom the equipment
was purchased. Should your BEHRINGER dealer not be located
in your vicinity, you may directly contact one of our subsidiaries.
Corresponding contact information is included in the original
equipment packaging (Global Contact Information/European
Contact Information). Should your country not be listed, please
contact the distributor nearest you. A list of distributors can be
found in the support area of our website (www.behringer.com).
Registering your purchase and equipment with us helps us
process your repair claims quicker and more efficiently.
Fig. 2.2: BX4410/BX4410A front panel (section 2)
Thank you for your cooperation!
The BASS control in the EQ section allows you to boost or
cut the bass frequencies at approx. 50 Hz.
Press the DEEP switch to add low frequencies (ranging
from 30 - 200 Hz) to your bass sound. When the DEEP
function is switched on, the LED above the switch lights up.
2. CONTROL ELEMENTS
2.1 Front panel
This control governs the upper bass-frequency range at
approx. 140 Hz.
The MIDDLE control allows you to boost/cut the low
midrange frequencies at approx. 500 Hz.
This control raises/lowers the high midrange frequencies
at approx. 1.6 kHz.
The TREBLE control governs the high-frequency range
on your BX4410/BX4410A at approx. 7.5 kHz.
Use this switch to enable/disable the BRIGHT effect, which
adds some brilliance to the treble frequencies in the range
from 2 - 20 kHz. When the BRIGHT function is on, its
respective LED lights up.
Fig. 2.1: BX4410/BX4410A front panel (section 1)
The LEVEL VU meter reads the level that is applied to the
preamp circuitry of the BX4410/BX4410A.
+
If the GAIN control
the VU meter reads the input level only. Selecting
“Active” instead of “Passive” is recommended
is set fully counterclockwise,
if the input level appears too high (in the right-hand
third of the VU meter). Use the GAIN control to set
the amplifier properly (so that the meter is in the
mid region). The overall volume can be adjusted
with the OUTPUT control
.
These are the inputs for your electric bass guitar. The
PASSIVE jack is for passive basses, the ACTIVE jack for
active instruments with high output levels. The ACTIVE
jack features 10 dB less gain.
Fig. 2.3: BX4410/BX4410A front panel (section 3)
When you enable the SHAPE filter with switch
can use the SHAPE control to modify the filter sound. The
, you
filter position is adjustable in the range from 120 Hz - 1.2 kHz.
Use the GAIN control to determine the input gain on your
BX4410/BX4410A.
The SHAPE switch activates the SHAPE filter. When the
filter is on, the LED above the switch lights up.
Connect your footswitch to the FOOTSWITCH jack, so
as to control the sub-harmonics processor and SHAPE
filter.
Use the OUTPUT control to determine the overall volume
of your BX4410/BX4410A.
With the sub-harmonics processor switched on (see
)
you can add ultra-low bass frequencies to your sound by
turning the ULTRABASS control (see chapter 5).
Press the ULTRABASS switch to enable the sub-harmonics
processor: The LED above the switch lights up.
2. CONTROL ELEMENTS
5
ULTRABASS BX4410/BX4410A
+
When the built-in limiter is activated, the LED below
the OUTPUT control lights up.
Connect the SEND/TUNER output to the input of your
effects device, for example, our proven multi-effects
processor BEHRINGER VIRTUALIZER PRO DSP2024P.
This output can also be used to connect your tuner.
Connect the RETURN jack to the output of your effects
device. Since the BX4410/BX4410A features a serial
effects path, the mix ratio must be set on your effects
device.
Use the balanced D.I. XLR output to feed the audio signal
from your ULTRABASS to an external mixing console. The
D.I. signal is wired post-EQ.
Use the LINE OUT jack to connect your BX4410/BX4410A
to a mixing console that has no balanced inputs and/or to
provide a signal that is independent of all settings adjusted
on the BX4410/BX4410A.
Fig. 2.5: BX4410/BX4410A rear panel (section 2)
The internal speakers of the BX4410/BX4410A are
connected to the 1/4" SPEAKER output jacks. They can
also be used to connect external loudspeakers. For further
speaker connection you find a professional loudspeaker
connector (compatible to Neutrik® Speakon®).
+
The LINE OUT output is wired post effects loop
&
and can also be used to feed the output signal
of your BX4410/BX4410A to an external bass amp.
+
+
Your speaker cabinets should have a sufficient
power rating (>450 W) and preferably a total
impedance of 4 W to avoid speaker damage. Too
high a load impedance will decrease the output
power rating of the power stage!
2.2 Rear panel
For correct speaker connection please also refer
to chapters 3.3, 3.3.1 and 6.2.1!
3. WIRING EXAMPLES
This chapter is aimed at describing and illustrating basic wiring
examples.
3.1 Standard setup comprising footswitch
and external loudspeaker
The standard setup is intended for rehearsals, sessions and
club gigs.
Fig. 2.4: BX4410/BX4410A rear panel (section 1)
Use the POWER switch to switch the BX4410/BX4410A
on or off. You should always make sure that the POWER
switch is in the “Off” position when initially connecting the
unit to the mains.
To disconnect the unit from the mains, pull out the main cord
plug. When installing the product, ensure that the plug is
easily accessible. If mounting in a rack, ensure that the
mains can be easily disconnected by a plug or by an all-pole
disconnect switch on or near the rack.
+
Please note: Merely switching the unit off does not
mean that it is fully disconnected from the mains.
When not using the unit for prolonged periods of
time, please unplug the unit’s power cord from the
power outlet.
MAINS CONNECTION. Use the power cord supplied with
the unit to connect it to the mains.
FUSE HOLDER/VOLTAGE SELECTOR. Before
connecting the unit to the mains, make sure that the voltage
setting matches your local voltage. A blown fuse should
only be replaced by a fuse of the same type and rating. On
some units, the fuse holder can be switched to one of two
positions, i.e. 230 V and 120 V. When operating the unit
outside Europe at 120 V, a higher fuse rating is required.
SERIAL NUMBER.
Fig. 3.1: Standard setup
6
3. WIRING EXAMPLES
ULTRABASS BX4410/BX4410A
3.3.1 Calculating the total impedance when
connecting several loudspeakers
If several speakers are used in parallel, their total impedance
can be calculated as follows:
3.2 Expanded setup with tuner and
connection to a mixing console
The wiring scheme shown here builds on the standard setup.
E.g. this would allow two 8 W loudspeakers ...
... or 1 x 8 W and 2 x 16 W:
Fig. 3.2: Expanded setup
The output signal of your BX4410/BX4410A can be taken
directly at the XLR D.I. output and fed to a microphone input of
your mixing console using a balanced microphone cable. Please
ensure that phantom power is switched off on the respective
channel of your mixer!
+
Please note that varying loudspeaker impedances
result in different output power delivered to the
individual speaker cabinets.
+
The D.I. output signal of your BX4410/BX4410A is
independent of the OUTPUT control’s setting.
However, it depends on all remaining settings and
the effects loop.
3.4 Connection of a multi-effects processor
Use the SEND/TUNER jack to connect the bass signal to a
multi-effects device or a compressor. The output level is
independent on the position of the OUTPUT control.
+
If you own a tuner that is able to loop through and
mute the signal, we recommend connecting it to
The RETURN jack should be connected to the output of your
effects device. If this jack is used for connection, the direct
signal is interrupted automatically. The ratio between direct and
effects signal has to be set on your effects device.
the effects loop
and
. This allows you to mute
the output signal as long as you tune your instrument.
3.3 Connecting several loudspeakers
Needless to say, you can connect several loudspeakers (three
at the most) to the speaker outputs of your BX4410/BX4410A,
which are wired in parallel. The figure below illustrates an
example for such a connection.
Fig. 3.4: Connection of a multi-effects processor
3.5 Setup for master/slave operation
3.5.1 ULTRABASS BX4410/BX4410A as master
The LINE OUT jack allows you to connect the BX4410/BX4410A
to an external power amp, using a commercial instrument cable
equipped with mono phone plugs. The signal present here is
independent on the position of the OUTPUT control.
3.5.2 ULTRABASS BX4410/BX4410A as slave
controlled by an external amp/preamp
To use the power amp of your ULTRABASS for an external
amp or preamp, you need to connect the line output of the
external amplifier to the RETURN jack on your BX4410/BX4410A.
The connected signal can be taken at the D.I. output. Use the
OUTPUT control to set the volume level.
Fig. 3.3: Connection of two speaker cabinets
+
If several speakers are used in parallel, the total
impedance should not drop below 4 W!
3. WIRING EXAMPLES
7
ULTRABASS BX4410/BX4410A
4. SHAPE FUNCTION
6. INSTALLATION
The SHAPE function on your BX4410/BX4410A provides a
revolutionary type of filter that you can use to modify your bass
sound in full detail. The filter allows you to shape your sound—
which is a must for bass players today. Extreme filter settings
will give your bass sound more power, for example:
6.1 Mains connection
The mains connection is made by using the enclosed mains
cable and a standard IEC receptacle. It meets all of the
international safety certification requirements.
+
Please make sure that all units have a proper
ground connection. For your own safety, never
remove or disable the ground conductor of the unit
or of the AC power cable.
You want to play a live bass solo but the sound doesn’t cut
through. The solo should stand out, rather than being drowned.
Set up a solid basic sound plus a very distinctive solo sound
using the SHAPE filter. Connect your footswitch to control the
SHAPE filter.
6.2 Audio connections
The SHAPE filter is a bargain when you are using two different
bass guitars. Maybe you want to change from a jazz bass to a
fretless bass, and vice versa—two instruments with a completely
different sound. During gigs you often lack the time to set up
your amp for a different instrument, so you’ll be happy to have a
BX4410/BX4410A, because you can use the SHAPE filter for
your fretless sound, and the basic sound for the jazz bass.
The BEHRINGER ULTRABASS is equipped with mono phone
jacks, except for the D.I. output which is on a balanced XLR
connector. The speaker jacks are on 1/4" TS and professional
speaker connectors (compatible to Neutrik® Speakon®).
5. ULTRABASS FUNCTION
Extremely low bass sounds playing one octave below the
lowest available bass guitar frequency are quite trendy in current
music productions. Often, you can do this in studios only, because
most bass amplifiers have no sub-harmonics function. Not so
with your BX4410/BX4410A: the ULTRABASS processor gives
you the ultimate tool to shape up-to-date sounds.
You’ll be surprised how deep your bass can sound with the
ULTRABASS function of your BX4410/BX4410A. Extreme
settings can be particularly interesting if you want to give your
sound some flavor in the treble range. By the way: when you
use the SHAPE filter set to a low cut-off frequency (which is a
nice setting for growling sounds), but feel that there’s not enough
power in the bass range, the sub-harmonics processor will be
there to help you: even though the sound is still growling, now it
has much more depth.
Fig. 6.1: 1/4" TS connector
The ULTRABASS function can easily be switched on and off
via the supplied footswitch. This allows you to fine-tune certain
passages only.
Fig. 6.2: 1/4" TRS connector
Fig. 6.3: XLR connectors
6. INSTALLATION
8
ULTRABASS BX4410/BX4410A
+
Please ensure that only qualified personnel install
7. SPECIFICATIONS
and operate the BX4410/BX4410A. During installation
and operation the user must have sufficient
electrical contact to earth. Electrostatic charges
might affect the operation of the unit.
AUDIO INPUTS
Active instrument input
Input impedance
Passive instrument input
Input impedance
Return
1/4" TS connector, unbalanced
approx. 220 kW unbalanced
1/4" TS connector, unbalanced
approx. 730 kW unbalanced
1/4" TS connector, unbalanced
approx. 15 kW unbalanced
6.2.1 Loudspeaker connections
In total, your BX4410/BX4410A features three loudspeaker
connectors.
Input impedance
AUDIO OUTPUTS
Send/Tuner
Output impedance
Line Out
Output impedance
Output level
D.I. output
Output impedance
Output level
Loudspeaker connectors
+
When connecting loudspeakers to the 1/4" jack
connectors, please switch off the device first.
Power up the unit again after all connections have
been made.
1/4" TS connector, unbalanced
min. 2 kW unbalanced
1/4" TS connector, unbalanced
approx. 100 W unbalanced
max. +20 dBu
XLR connector, servo-balanced
approx. 100 W balanced
max. 0 dBu
1/4" TS connector, unbalanced
professional connector
(compatible to Neutrik® Speakon®)
min. 4 W
Please use a speaker compatible to Neutrik® Speakon® if you
want to connect one speaker cabinet only. For optimum output
power delivered to the speaker(s), use your BX4410/BX4410A
in combination with one 4 W or two 8 W cabinets.
Your BX4410/BX4410A is equipped with high-quality
connectors compatible to Neutrik® Speakon®, which ensure safe
and trouble-free operation. These connectors were especially
developed for high-power loudspeakers. Once it is plugged in, it
safely locks into its position and cannot be accidentaly
disengaged. It prevents the occurrence of electrical shock and
ensures the correct polarity.
Load impedance
SYSTEM SPECIFICATIONS
Power amp output
450 Watts into 4 W
SPEAKERS
High-power bass speakers
4 x 10" BUGERATM Hard Attack
Aluminum cone speakers
(BX4410A)
4 x 10" BUGERATM Classic Tone
bass speakers (BX4410)
94 dB @ 1 W / 1 m
max. 119 dB
Sensitivity
SPL
Impedance
8 W
Frequency response
Power (program)
Tweeter
46 Hz - 16 kHz
300 W
1" tweeter driver
5 kHz - 16 kHz
Frequency response
POWER SUPPLY
Mains voltages
U.S./Canada
120 V~, 60 Hz, 6 A
China/Korea
220 V~, 50 Hz, 3 A
Europe/U.K./Australia
230 V~, 50 Hz, 3 A
Japan
Fig. 6.4: Professional connector compatible to
Neutrik® Speakon®
100 V~, 50 - 60 Hz, 6 A
General export model
120/230 V~, 50 - 60 Hz
100 - 120 V~: T 10 A H 250 V
220 - 240 V~: T 6.3 A H 250 V
Standard IEC receptacle
Fuse
Mains connection
PHYSICAL/WEIGHT
Dimensions (H x W x D)
approx. 33" (840 mm)
x 26 3/4" (680 mm)
x 16 1/3" (415 mm)
Weight
approx. 60.5 kg (133.4 lbs)
BEHRINGER constantly strives to maintain the highest quality standards. Modifi-
cations may be made, if necessary, without prior notice. The specifications and appearance
of the equipment may therefore differ from those listed or illustrated.
7. SPECIFICATIONS
9
ULTRABASS BX4410/BX4410A
2. If the product needs to be modified or adapted in order to
8. WARRANTY
comply with applicable technical or safety standards on a national
or local level, in any country which is not the country for which the
product was originally developed and manufactured, this
modification/adaptation shall not be considered a defect in
materials or workmanship. The warranty does not cover any such
modification/adaptation, irrespective of whether it was carried out
properly or not. Under the terms of this warranty, BEHRINGER shall
not be held responsible for any cost resulting from such a
modification/adaptation.
§ 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW
1. This warranty does not exclude or limit the buyer’s statutory
rights provided by national law, in particular, any such rights against
the seller that arise from a legally effective purchase contract.
2. The warranty regulations mentioned herein are applicable
unless they constitute an infringement of national warranty law.
§ 2 ONLINE REGISTRATION
3. Free inspections and maintenance/repair work are expressly
excluded from this warranty, in particular, if caused by improper
handling of the product by the user. This also applies to defects
caused by normal wear and tear, in particular, of faders, crossfaders,
potentiometers, keys/buttons, tubes, guitar strings, illuminants and
similar parts.
Please do remember to register your new BEHRINGER
conditions of our warranty carefully.
Registering your purchase and equipment with us helps us process
your repair claims quicker and more efficiently.
4. Damages/defects caused by the following conditions are not
covered by this warranty:
Thank you for your cooperation!
s
s
s
improper handling, neglect or failure to operate the unit in
compliance with the instructions given in BEHRINGER user
or service manuals.
§ 3 WARRANTY
1. BEHRINGER (BEHRINGER International GmbH including all
BEHRINGER subsidiaries listed on the enclosed page, except
BEHRINGER Japan) warrants the mechanical and electronic
components of this product to be free of defects in material and
workmanship for a period of one (1) year* from the original date of
purchase, in accordance with the warranty regulations described
below. If the product shows any defects within the specified warranty
period that are not excluded from this warranty as described under
§ 5, BEHRINGER shall, at its discretion, either replace or repair the
product using suitable new or reconditioned parts. In the case that
other parts are used which constitute an improvement, BEHRINGER
may, at its discretion, charge the customer for the additional cost
of these parts.
connection or operation of the unit in any way that does
not comply with the technical or safety regulations
applicable in the country where the product is used.
damages/defects caused by force majeure or any other
condition that is beyond the control of BEHRINGER.
5. Any repair or opening of the unit carried out by unauthorized
personnel (user included) will void the warranty.
6. If an inspection of the product by BEHRINGER shows that the
defect in question is not covered by the warranty, the inspection
costs are payable by the customer.
2. If the warranty claim proves to be justified, the product will be
returned to the user freight prepaid.
7. Products which do not meet the terms of this warranty will be
repaired exclusively at the buyer’s expense. BEHRINGER will inform
the buyer of any such circumstance. If the buyer fails to submit a
written repair order within 6 weeks after notification, BEHRINGER
will return the unit C.O.D. with a separate invoice for freight and
packing. Such costs will also be invoiced separately when the
buyer has sent in a written repair order.
3. Warranty claims other than those indicated above are expressly
excluded.
§ 4 RETURN AUTHORIZATION NUMBER
1. To obtain warranty service, the buyer (or his authorized dealer)
must call BEHRINGER (see enclosed list) during normal business
hours BEFORE returning the product. All inquiries must be
accompanied by a description of the problem. BEHRINGER will
then issue a return authorization number.
§ 6 WARRANTY TRANSFERABILITY
This warranty is extended exclusively to the original buyer
(customer of retail dealer) and is not transferable to anyone who
may subsequently purchase this product. No other person (retail
dealer, etc.) shall be entitled to give any warranty promise on
behalf of BEHRINGER.
2. Subsequently, the product must be returned in its original
shipping carton, together with the return authorization number to
the address indicated by BEHRINGER.
§ 7 CLAIM FOR DAMAGES
3. Shipments without freight prepaid will not be accepted.
Failure of BEHRINGER to provide proper warranty service shall
not entitle the buyer to claim (consequential) damages. In no
event shall the liability of BEHRINGER exceed the invoiced value
of the product.
§ 5 WARRANTY REGULATIONS
1. Warranty services will be furnished only if the product is
accompanied by a copy of the original retail dealer’s invoice. Any
product deemed eligible for repair or replacement under the terms
of this warranty will be repaired or replaced.
* Customers in the European Union please contact BEHRINGER
Germany Support for further details.
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time of printing. The names
of companies, institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners. Their use
neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the trademark owners with BEHRINGER. BEHRINGER accepts no
liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained
herein. Colours and specification may vary slightly from product. Products are sold through our authorised dealers only. Distributors and dealers are not
agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. No part of this
manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for
any purpose, without the express written permission of BEHRINGER International GmbH. BEHRINGER® is a registered trademark.
ALL RIGHTS RESERVED. © 2006 BEHRINGER International GmbH,
Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany.
Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
10
8. WARRANTY
|