®
ELECT RO N ICS CO RP.
XM® SATELLITE DIGITAL AUDIO
RECEIVER SYSTEM MODEL SRXM-001
INSTALLATION MANUAL
FOR USE WITH THE RADIO RECEIVER
UNIT (RRU) MODEL XM-RCV
For Custom er Service
Visit Our W ebsite At
WWW.audiovox.com
Product Inform ation, Photos,
FAQ’s O wner’s M anuals
INSTALLATIONandWIRINGPRECAUTIONS
1. To prevent a short-circuit, Be sure to turn off the ignition and remove the negative (-)
battery cable, prior to installation. Connect power wires last.
NOTE: If the SRXM-001 System is to be installed in a car that is equipped with an on-board
drive or navigation computer, do not disconnect the battery cable. If the cable is discon-
nected, the computer memory may be lost. Under these conditions, use extra caution during
installation not to cause a short circuit.
2. Do not install the unit in the following locations:
Locations exposed to direct sunlight.
Where hot air is discharged from the car heater.
Inareassubjecttoextremetemperatures.
3. Incorrectinstallationmaycausedamagetothesystem. Mounttheunitfirmlyinplace,using
the supplied brackets and screws.
4. Be careful not to damage the car wiring.
5. Be sure to use the supplied screws and washers.
6. Be careful not to snag any wires when tightening screws.
3
PACKING LIST
SRXM-001 MAIN SYSTEM COMPONENTS
(NOTE: Components are not drawn to scale.)
RADIORECEIVERUNIT(RRU)
Model # XM-RCV
SATELLITESYSTEMCONTROL
UNIT(SCU)
FM MODULATOR /
CONTROL INTERFACE
Model # SAT-COM
1
4
7
2
5
8
0
3
6
9
AUDIO OX
R E
W
P O
SFT
AUDIO OX
AUDIO OUT
TER.
SAT.
R
L
DIN OUT
1 pc.
(P/O SAT-COM)
1 pc.
1 pc.
INSTALLATION PARTS
Self-tapping Screws (5mm x 15mm), with
Flat Washers and Lock Washers
(Used to mount RRU to mounting surface)
PhillipsRound
Head. Screw
(4mm x 12mm)
PhillipsRoundHead
Screw (4mm x 8mm)
(Used to mount
RRU Mounting
Brackets
(Used to mount FM MOD
to mounting surface)
bracket to RRU)
4 pc.
(P/O XM-RCV)
4 pc.
(P/O SAT-COM)
2 pc.
(P/O XM-RCV)
4 pcs. each
(P/O XM-RCV)
FMModulatorControl
Interface Wire Harness
PhillipsRoundHead
Screw (4mm x 8mm)
w/ External Tooth Washer
(Used to mount SCU to mounting
surface)
Din Cable, 13- pin
(6 Meter)
To connect the RRU to the FM Modula-
tor / Control Interface
4 pcs. each
1 pc.
(P/O XM-RCV)
1 pc.
(P/O XM-RCV)
(P/O SAT-COM)
RCAtoRCACable
(6 Meter)
To connect the RRU to the FM Modula-
OPTIONAL
SUPPLIED
tor / Control Interface
ACCESSORIES
ACCESSORIES
Owner's
Manual
Quick
Reference
Card
Satellite Radio
Trim Ring,
Satellite Control
Model #SAT-PF
1 pc.
(P/O XM-RCV)
Wireless Remote
Control Model
#SAT-RC
Hook & Loop
AdhesiveTape
1 cut set.
(P/O SAT-COM)
1 pc.
(P/O SAT-COM)
1 pc.
(P/O SAT-COM)
4
TYPICAL FM MODULATED SYSTEM
INSTALLATION
6
9
T
2
5
8
0
SF
1
4
7
R E
W
P O
5
TYPICALAUXILLARYAUDIOSYSTEM
INSTALLATION
3
6
9
T
2
5
8
0
SF
1
4
7
R E
W
P O
6
TYPICAL FM MODULATED INSTALLATION for
SRXM-001 SYSTEM COMPONENT LAYOUT
Ground (BLACK)
Attach this wire to the chassis of the car. Be
sure that the surface is free of paint and is
not rusty. If a proper ground connection is
not made, the SRXM-001 System may not
operate correctly and stray noise may be
picked up by the unit.
From Existing
Vehicle Antenna
FMRadio
Satellite Radio
Antenna
(Purchased
Separately)
SCU
To FM Radio
Antenna input
+12V Battery
(YELLOW)
Connect this wire to
a terminal which is
always energized.
FMModulator
DINCable
FilterBox
& Fuses
RRU
RCAtoRCA
Cable
+12V Accessory / Ignition (RED)
Connect this wire to a terminal which
is energized when the ignition switch
is turned to the "ON" or "ACCESSORY"
position.
13-Pin
DINCable
Self-Tapping
PhillipsHead
Screw
MOUNTING THE FM MODULATOR
Install the FM Modulator to the mounting surface with the
self-tapping screws (4mm x 12mm).
7
SYSTEM INSTALLATION
RADIORECEIVERUNIT(RRU)
PROCEDURE for HORIZONTAL INSTALLATION of the RRU
Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head
Screws (4mm x 8mm).
1.
Bracket
Phillips Head Screws (4mm x
8mm) used in 4 places
Determine the mounting location and drill 4x 1/8” (4mm) mounting holes.
2.
WARNING
Never mount the unit near the fuel tank.
Carpet
4x 1/8” (4mm)
mounting holes
NOTE:If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from
catching on carpet. Cut holes in carpet before drilling into subsurface.
Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and
LockWashers. UseRTV(siliconesealer)onscrewthreadsoraroundtheholestoprevent
moistureintrusion.
3.
RRU
Self-tapping Screw
(5mm x 15mm), w/Flat
Washers and Lockwashers
Carpet
used in 4 places
Bracket
8
PROCEDURE for VERTICAL INSTALLATION of the RRU
Attach a mounting bracket to each side of the RRU, using the 4 Phillips Round Head
Screws (4mm x 8mm).
1.
RRU
Phillips Head Screws (4mm x
8mm) used in 4 places
Bracket
Determine the mounting location and drill 4 x 1/8” (4mm) mounting holes.
2.
WARNING
Never mount the unit near the fuel tank.
Carpet
4x 1/8” (4mm)
mounting holes
NOTE:Ifmountingsurfaceiscarpeted,usecautionwhendrillingholestopreventdrillbitfrom
catching on carpet. Cut holes in carpet before drilling into subsurface.
Mounttheunitinplace,using4Self-tapping Screws(5mmx15mm),w/FlatWashersandLock
Washers. UseRTV(siliconesealer)onscrewthreadsoraroundtheholestopreventmoisture
3.
intrusion.
RRU
Self-tapping Screw
(5mm x 15mm), w/Flat
Washers and Lockwashers
used in 4 places
Carpet
Bracket
9
PROCEDURE for the MOUNTING of the RRU UNDER THE REAR DECK
Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head
Screws (4mm x 8mm).
1.
Bracket
Phillips Head Screws
used in 4 places (4mm x 8mm)
2.
Determine the mounting location and drill four 4mm mounting holes.
Underside of
Rear Deck
4x 1/8” (4mm)
mounting holes
(4 places)
Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and
Lock Washers.
3.
Rear
Deck
Self-tapping Screw
(5mm x 15mm), w/Flat
Washers and Lockwashers
used in 4 places
10
INSTALLINGTHESATELLITESYSTEMCONTROLUNIT(SCU)
PROCEDURE for a TYPICAL INSTALLATION of the SCU USING HOOK &
LOOP ADHESIVE TAPE (SUPPLIED)
1.DeterminewheretheSCUistobelocated(flatsurface)NOTE:Thechosenpositionmustallow
aclearviewofthedisplayandeasyaccesstothecontrolsforboththeDriverandPassenger
ofthevehicle.
2.UsinganAlcoholSwab,cleananddrytheentiresurfaceareawheretheSCUistobemounted
and the back surface of the SCU.
3. Remove the protective paper from the back of the first piece of the supplied Hook & Loop
Adhesive Tape (Loop side) and apply it to the mounting surface (see Figure 1.)
4.RemovetheprotectivepaperfromthebackofthesecondpieceofthesuppliedHook&Loop
AdhesiveTape(Hookside)andapplyittothebacksideoftheSCU(seeFigure2.). Position
theSCUcableintheappropriatedirectionalchannelonthebackoftheSCUsothattheback
surface is flat (see Figure 3.).
5. Carefully press the SCU into place.
Velcro Tape (Loop)
Hook&LoopAdhesiveTape(Hook)
Figure 2.
Figure 1.
Figure 3.
NOTE:
Donotinstalltheunitinthefollowinglocations:
InLocationsexposedtodirectsunlight.
Where hot air is discharged from the car heater.
Inareassubjecttoextremetemperatures.
11
PROCEDURE FOR A TYPICAL BRACKET INSTALLATION OF THE SCU
(Bracket not supplied)
Audiovox suggests this type of installation over the Hook & Loop type of installation though the Hook & Loop
installation (if done correctly) is a secure and sufficient mounting option. Installation of the SCU using a
bracket results in a professional, factory-installed look, without visibly damaging the interior of the vehicle.
When combined with the optional Trim Ring (model #SAT-PF) the results are further cosmetically en-
hanced. There are several types of brackets available to accomplish this type of installation.
The installation procedure that follows, illustrates the use of a Pro.Fit® mounting bracket. Audiovox has
found that the Pro.Fit® VSM® line of mounting brackets are easy to install and compliments the installation
of the SCU as well as being a perfect match to the optional Trim Ring (model #SAT-PF). Pro.Fit® VSM®
mounting bracket reduce the installation liability while maintaining the resale value of a car because of the
professional fit, professional look and safe design.
Currently Pro.Fit® VSM® offers hundreds of brackets, covering most popular cars, vans, and trucks. Step-
by-step instructions and technical support are available for every mount and application.
After the proper mounting bracket has been selected and installed using the Original Manufacturers
installation instructions, proceed with the following steps:
1. Feed the SCU Cable through the hole in the Trim Ring (optional) and connect it to the
RF Modulator.
2. Using the Phillips Head Screws and the External Tooth Lock Washers (supplied),
Mount the SCU to the bracket as shown in the Figure below.
NOTE: Use caution not to over tighten the screws into the back of the SCU as this may
cause damage to the unit.
Do not install the unit in the following locations:
In Locations exposed to direct sunlight. Where hot air is discharged from the car heater. In areas
subject to extreme temperatures.
NOTE:
(Example installation position)
Phillips Round Head Screw (4mm x 8mm)
1
4
2
5
3
6
7
8
9
0
SFT
External Tooth Washer
(4mm int.)
Bracket
(Not Supplied)
Bracket Shown is a PRO.FIT for ordering information
visit www.pro-fit-intl.com
SCU
TrimRing
(Not Supplied, Model #SAT-PF)
For ordering information call Audiovox Electronics toll-free telephone assis-
tance line at 1-800-645-4994 or contact us via the web:
Upon completion of the SCU installation and before the XM radio is activated a test of the system should be
performed. To verify that the SRXM-001 system and the antenna have been installed correctly and are
functioning, select and listen to CH 1. (XM preview channel). If there is no power to the SCU check that all
connections have been made and that fuses are good. If there is no signal present, make sure that the
antenna is unobstructed (move vehicle) and check the antenna cable connection to the RF Modulator. For
a detailed trouble-shooting guide, refer to the Owner’s Manual.
128-6213A
© Copyright 2001 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788
12
|