Audiovox Remote Starter 128 8121 User Manual

From APS687 Change Transmitters to 07SP 05/07 add door lock

section

128-8121

1 of 24

128-8121

3 of 24

Action

System Response

Turn ignition on

No response

Press and release the valet switch 3 times

Within 3 seconds, turn ignition Off, On, Off, On

This Action Accesses Feature Bank 3 Remote Start Selectable Features

1 Chirp - LED 1 flash

Short chirp, then 2 long chirps

First

Press the valet switch one time

Press transmitter Lock button to change

1 chirp = defrost output pulsed

2 chirps = defrost output 10 Mins

Second

Third

Press and release the valet switch

Press transmitter Lock button to change

2 chirps = RF start chirp on

1 chirp = RF start chirp off

Press and release the valet switch

Press transmitter Lock button to change

2 chirps = run time set for 10 mins

3 chirps = run time set fro 15 mins

4 chirps = run time set for 20 mins

1 chirp = run time set for 5 mins

Fourth

Fifth

Press and release the valet switch

Press transmitter Lock button to change

1 chirp = parking lights on steady w/RS active

2 chirps = parking lights flashing w/RS active

Press and release the valet switch

Press transmitter Lock button to change

2 chirps = tachometer input checking

1 chirp = voltage sense input checking

Sixth

Press and release the valet switch

Press transmitter Lock button to change

1 chirp = greater than 0.5 V check before start

2 chirps = less than 0.5 V check before start

Seventh

Press and release the valet switch

Press transmitter Lock button to change

2 chirps = ign 2 on during crank

3 chirps = ign 2 same as accessory

1 chirp = ign 2 off during crank

Eighth

Press and release the valet switch

Press transmitter Lock button to change

Press and release the valet switch

Press transmitter Lock button to change

Press and release the valet switch

Press transmitter Lock button to change

Press and release the valet switch

Press transmitter Lock button to change

2 chirps = ign 3 on during crank

3 chirps = ign 3 same as accessory

4 chirps = Ign 3 same as starter

1 chirp = ign 3 off during crank

Ninth

Tenth

1 chirp = diagnostics off

2 chirps = diagnostics on

2 chirps = crank time 1.0 sec

3 chirps = crank time 1.5 sec

4 chirps = crank time 2.0 sec

1 chirp = crank time 0.8 sec

Eleventh

Twelfth

1 chirp = unit set for gasoline engine

2 chirps = unit set for diesel engine 10 sec delay

3 chirps = unit set for diesel engine 15 sec delay

4 chirps = unit set for diesel engine 20 sec delay

Press and release the valet switch

Press transmitter Lock button to change

1 chirp = transponder output while R/S active

2 chirps = transponder output during start only

3 chirps = transponder output until ignition turned off

Thirteenth

Fourteenth

Fifteenth

Press and release the valet switch

Non Functional On This Unit

Press and release the valet switch

Press transmitter Lock button to change

1 chirp = crank averaging w/voltage input checking

2 chirps = preset crank time w/voltage input check

Non Functional On This Unit

Sixteenth

Press and release the valet switch

Press transmitter Lock button to change

1 chirp = turbo timer off

2 chirps = turbo timer 3 mins

3 chirps = turbo timer 5 mins

4 chirps = turbo timer 10 mins

Seventeenth

Press and release the valet switch

Press transmitter Lock button to change

Press and release the valet switch

1 chirp = aux o/p Black/Blue single pulse

2 chirps = aux o/p Black/Blue as alarm feature #1

turn the ignition off to:

Exit Programming Mode

Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the

programming will be terminated.

128-8121

4 of 24

This system is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combina-

tion Keyless Entry/Remote Start unit is a sophisticated system with many advanced features, IT MUST

NOT be installed into a vehicle with a manually operated transmission. Doing so may result in serious

personal injury and property damage.

MUST HAVE a Tach Signal Input, and an Automatic Transmission.

INSTALLATIONOFTHEMAJORCOMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting

location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin

main wiring harness.

Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the

module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around

or block the steering wheel preventing proper control of the vehicle. Secure the module in the chosen

location using cable ties or screws as necessary.

Note: Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

HOOD PIN SWITCH:

The hood pin switch included in this package is required for the safety shut down of the remote start unit. If

the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF com-

mand to start is issued. This hood pin switch MUST be installed in all applications. Failure to install the

hood pin switch may result in personal injury or property damage. Mount the hood pin switch in an area

under the hood that is away from water drain paths. If necessary, the included brackets may be used to

move the hood pin switch away from rain gutters or allow mounting to the firewall behind the hood seal. In

either case the hood pin switch must be set up to allow the hood to depress the switch at least 1/4" when

the hood is closed and fully extended when the hood is opened. For direct mounting, a 1/4" hole must be

drilled. Carefully check behind the chosen location to insure the drill will not penetrate any existing factory

wiring or fluid lines. Drill a 1/4" hole in the desired location and thread the hood pin switch into it using a 7/

16" nut driver or deep well socket. If using the mounting bracket, first secure the bracket to the desired

location and secure the hood pin switch in the pre-threaded mounting bracket hole.

PUSHBUTTON LED SWITCH

Select a mounting location known and accessible to the operator of the vehicle. A dash knockout plug or

front dash panel is desirable as the now Pushbutton LED assembly needs the LED to be visible from the

outside of the vehicle and will be used for valet modes, programming features, programming transmitters,

and for overriding the remote start unit when the vehicle is being serviced. Inspect behind the chosen

location to insure that adequate clearance is allowed for the body of the switch, and also that the drill will not

penetrate any existing factory wiring or fluid lines. Drill a 5/16" or 8mm hole in the desired location and

mount the switch by passing the connectors, one at a time, through the panel from the front side and

pressing on the bezel until the switch is fully seated.

THE RECEIVER/ANTENNAASSEMBLY:

The ReceiverAntennaAssembly provided with this unit allows routing from below the dashboard for maxi-

mum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.

Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded

window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear

window location for best reception. Secure the antenna with double stick tape provided. After securing the

antenna with tape, we advise also securing a section of the antenna cable to a fixed support. This will

prevent the antenna from dropping down in case the double stick tape is exposed to extreme heat, which

may loosen its gummed surface. Route the connector toward the control module using caution not to pinch

the cable as this will cause poor or no RF reception to the control module.

128-8121

5 of 24

start relay and the accessory relay.

This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit

provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire

is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the

RF signal is received with no delay. Regardless of the vehicle, Gasoline or Diesel, for every installation, the

vehicle

I M P O R TA N T !

DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS

INTO THE CONTROL MODULE UNTILALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AF-

TER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BAT-

TERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKINGANY CONNECTIONS.

WIRING THE 6 PIN MAIN POWER HARNESS:

Note: Do not remove the fuse holders from this wire harness. Fuses must be used and located

as close as possible to the power source for adequate protection of the vehicle.

Fused RED w/ WHITE TRACE WIRE: + 12 volt Battery 1 Source

Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register voltage in all

positions of the ignition switch. Connect the Red w/White wire to the vehicle's battery wire. This wire

provides power for the control circuit as well as the ignition 1 and ignition 2 relays.

Fused RED WIRE: + 12 Volt Battery 2 Source

Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register voltage in all

positions of the ignition switch. Connect the Red wire to the vehicle's battery wire. This wire provides power

for the start relay and the accessory relay.

I M P O R TA N T !

IT IS THE RESPONSIBILITY OF THE INSTALLING TECHNICIAN TO DETERMINETHE LOAD FACTOR OF

THE VEHICLES ELECTRICALCIRCUITS WHEN THE VEHICLE IS RUNNINGANDTOADEQUATELYFUSE

THE TWO POWER WIRES BASED ON THAT LOAD. IF THE VEHICLE, RUNNING UNDER LOAD WITH

THEAIR CONDITIONER, HEATER BLOWER MOTOR,ANDACCESSORIES EXCEEDS 24AMPS CON-

TINUOUS, WE RECOMMEND THATTWO FUSES BE USED IN COMBINATION ON EACH POWER WIRE

AS SHOWN BELOW. FORADDITIONALINFORMATION SEE TECH UPDATE ISSUED 9/30/96.

YELLOW WIRE: Starter Output

Careful consideration for the connection of this wire must be made to prevent the vehicle from

starting while in gear. Understanding the difference between a mechanical and an electrical

Neutral Start Switch will allow you to properly identify the circuit and select the correct installa-

tion method. In addition you will realize why the connection of the safety wire is required for all

mechanical switch configurations.

Failure to make this connection properly can result in personal injury and property damage. In all installa-

tions it is the responsibility of the installing technician to test the remote start unit and assure that the

vehicle cannot start via RF control in any gear selection other than park or neutral.

In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wire will be

made to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts when

the ignition switch is turned to the start (crank) position only. This wire will have 0 volts in all other ignition

switch positions.

128-8121

6 of 24

Note: This wire must be connected to the vehicle side of the starter cut relay (when used). For the

electrical neutral switch configuration, this connection must be made between the starter inhibit

relay, (when used) and the neutral safety switch as shown in the following diagram.

Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal

injury and property damage.

SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.

BLUE WIRE: Ignition 1 Output

Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the

ignition key is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions and will have 0 volts

when the key is turned to the "OFF" and "ACCESSORY" positions.

For DieselApplications, this wire must be connected to the ignition circuit that powers the glow plugs if the

vehicle requires glow plug pre-heating.

GREEN WIRE: Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the

ignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.

This wire will show 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions.

Note: See programming information concerning this wire to allow output during the "START" mode.

VIOLET WIRE: Accessory Output

Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the

ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the

key is turned to the "OFF" and "START" or "CRANK" positions.

128-8121

7 of 24

WIRING THE 4 PINALTERNATE IGNITION HARNESS

ORANGE/BLACK Wire: Parking Brake Input

This wire is used only when the turbo timer mode, Bank 3, feature # 16 is selected ON. This input insures

that the vehicle parking brake is applied whenever the vehicle is set up for and the turbo timer circuit is used.

Thisinputmustswitchtogroundwhenthevehicle'sparkingbrakeisapplied.ConnecttheOrange/Blackwire

to the negative output of the vehicle's parking brake switch.

RED/BLACK Wire: + 12 Volts Input

Note: The Red/Black and Pink are dry contacts and may be used for negative switching when necessary.

Connecting the Red/Black to chassis ground will result in Pink being ground when the R/S is activated.

Thisinputistobeconnectedtoaseparate, (OtherthanthewireRedorRed/Whiteisconnectedto), constant

on + 12 volt source which will supply + 12 volt power to the additional ignition output, (Pink), wire. Connect

this wire to a separate + 12 Volt source.

PINK Wire: Additional Ignition Output

This wire can be used as an additional + 12 Volt ignition output supplied by the Red/Black wire. This output

can be selected to be on or off during the start cycle. (See feature bank 3 selection # 8) Connect this wire

to the third ignition circuit in the vehicle and set the selectable feature # 8 of Bank 3 according to the way in

which the vehicle's ignition switch operates.

Note: Do not remove the fuse holders from this wire harness. Fuses must be

used and located as close as possible to the power source for adequate

protection of the vehicle.

128-8121

8 of 24

WIRING CONNECTIONS: 12 Pin Input / Output Harness

Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid

clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self-

tapping screw and ring terminal.

GRAYWIRE:NegativeInhibitInput1

ConnecttheGRAYwiretothepreviouslymountedhoodpinswitchprovided. Thiswirewillberoutedthrough

the firewall into the engine compartment. It is necessary to use an existing grommet when passing wires

throughthefirewalltopreventshortcircuiting.Thisisanimportantsafetyfeatureof theSystem,failuretouse

thisfeaturecanresultinseriousinjury.Routethewiretothepinswitchandconnectitusingthebulletconnector

provided.

GRAYw/BLACKTRACERWIRE:NegativeInhibitInput2

Any time the gray w/ black tracer wire is grounded, the Remote Starter will stop operating, even if the signal

is received from the transmitter.

Ifthebrakelightswitchinthevehicleswitchesgroundtothebrakelightcircuit,connecttheGrayw/Blacktrace

wire to the output of the brake light switch. If the brake light switch in the vehicle switches +12 Volts, do not

use the Gray w/ Black wire; see Brown w/ Black tracer wire.

BROWN WIRE: Positive Inhibit Input 1

Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even if the signal is

receivedfromthetransmitter.

Ifthevehiclehasafactoryinstalledhoodpinswitchandthatswitchprovides+12Voltstoanunderhoodlight,

the Brown wire can be connected to the existing pin switch.

BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2

Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even

if the signal is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the

brake light circuit, connect the Brown w/ Black trace wire to the output of the brake light switch. If the brake

lightswitchinthevehicleswitchesground, donotusetheBrownw/Blackwire;seeGrayw/Blacktracerwire.

Brake Switch Positive Shutdown Detail

128-8121

9 of 24

YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output

Note: You must disconnect the ignition input of the alarm from any other wire that it is presently connected

to in the vehicle.

This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Volts when the ignition

key is “OFF” and when the vehicle is running under the control of the remote starter.

This wire should be connected to the ignition input of the alarm system.

The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/

unlock the doors while running under control of the remote start unit.

(2) WHITE Wires: Parking Light Flasher

These wires are the COMMON and NORMALLY OPEN contacts of the on-board parking lamp relay.

If the vehicle's parking lights are a +12 volt switched system, connect (1) of the White wires to a fused (15A max.)

+12 volt battery source, and connect the second White wire to the vehicle's parking light wire.

If the vehicle's parking lights are a chassis ground switched system, connect (1) of the White wires to a chassis

ground source, and connect the second White wire to the vehicle's parking light wire.

Switch

LIGHT BLUE Wire: Ignition 3 / Shock Disable Output

This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes,

and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of

the applications described below, a relay will be required. The Light Blue wire can be used to accommodate the

following situations:

A. Shock Sensor By Pass:

If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation

period, then vibration from the running vehicle can cause the alarm to trigger. In this case, connect the Light

Blue Wire to terminal #86 of a external relay. Connect terminal #85 of the relay to a fused + 12 volt battery

source. Cut the shock sensor trigger wire and connect one end of the cut wire to terminal #30 and the other end

of the cut wire to terminal #87a. Just before the Remote Start unit is activated, the relay contacts will open,

preventing the shock sensor's operation until the Remote Start unit shuts off.

B. Ignition 3 Output:

Some newer vehicles use a third ignition wire, which is required to start and keep the vehicle's engine running.

If this is the case, connect the Light Blue wire to terminal #86 of an external relay. Connect terminal #30 & #85

to a fused + 12 volt battery source rated for a minimum of 25 Amp. Connect terminal #87 to the third ignition wire

in the vehicle.

128-8121

10 of 24

C. GM VATS Key Override:

If the vehicle has the General Motors VATS system installed, you will need to bypass the system while the vehicle is

operating under the control of the Remote Start Unit. To Do This;

1. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of the key's

value from the resistor pack supplied.

2. Locate the pair of VATS wires in the vehicle, usually a pair of thin gauge wires running from the ignition switch

to the VATS control module.

Note: These wires are typically White w/ Black trace and Violet w/ Yellow trace, however in later model Cadillacs,

they are run through an orange sleeve, and are either both Black, both Yellow, or both White wires. Consult

the factory service manual for additional information.

3. Connect the Light Blue Wire from the Remote Start Unit to terminal #86 of an external relay. Connect terminal

#85 of the relay to a fused + 12 volt battery source.

4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the relay.

Connect the other side of the (#1) wire to terminal #30.

5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown).

Note: The above information and following diagram is for the GM VATS system only. For GM PASS LOCK System

you will require the Audiovox AS-PASS II Module.

General Motors VATS By-Pass Diagram

Tachometer Input Wiring Detail

GREEN/ORANGE Wire: Tach Sensor Input

This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module.

This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and

connect to the negative side of the ignition coil. This Remote Start unit learns the tach rate of the vehicle and in most

cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has a

single coil unit for each cylinder, it may be necessary to connect this wire to more than one cylinder for proper tach

reference. See multi coil wiring detail shown later in this manual for additional information.

128-8121

11 of 24

Green/Yellow Wire: Diesel Wait To Start Input

The Green/Yellow wire will connect to a diesel vehicles glow plug wire. When the unit receives a start command,

this wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by the

remote start unit, the glow plug circuit gets energized, (+ 12 volts), when the glow plug circuit of the vehicle drops the

+ 12 volts, which effectively grounds the wait to start input, then 500mS later the starter will engage. This wire can

also be connected to the Glow Plug Bulb wire in the vehicle if this bulb wire gets + 12 volts when the ignition comes

on and drops low when the glow plug circuits temperature is reached. Be sure to fuse the wire with a 1 Amp Fuse

when connecting to a high current circuit such as a factory glow plug wire. The fuse should be installed as close

to the high current wire as possible. If you are installing this unit in a Gasoline vehicle, this wire is not used.

Note: If the Glow Plug sense wire, Green/Yellow is connected, this wire will have priority over the setting of feature

Bank 3 Feature #11.

WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS

The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during

different stages of the Remote Start unit's operation. Understanding these outputs and the time in which

they occur will allow you to determine if they are needed for the particular vehicle you are working on as well

as how to use them.

Black w Blue Trace Wire: Pulsed Ground Output Before Start

The Black w/ Blue Trace wire will provide a 1 second 300 mA pulsed ground output 1.5 second before the

remote start unit activates as well as when the transmitter is used to disarm the system. Typical use for this

output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm

when the remote start unit engages or when the transmitter is used to unlock the doors.

Black w/ Light Green Trace Wire: Pulsed Ground Output After Start

The Black w/ Light Green Trace wire will provide a 1 second 300mA pulsed ground output after the vehicle is

started under control of the remote start unit. Typically this wire will be used to re-lock the vehicle doors if

the doors unlock automatically when the factory anti-theft system is disarmed.

Black w/ Red Trace Wire: Pulsed Ground Output After Shutdown

The Black w/ Red Trace wire will provide a 1 second 300 mA pulsed ground output after the remote start unit

shuts down. This output will occur regardless of whether the circuit times out or is manually terminated.

Typically this output will be used to re-lock the vehicle doors if the doors unlock automatically when the

ignition circuit transitions to off.

Black w/ Yellow Trace Wire: Ground Output During Start (Crank)

The Black w/ Yellow Trace wire will provide a 300 mAground output while the starter output of the remote

start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM

vehicles. This wire is also referred to as the ECM wake up wire in some Chrysler vehicles.

Note: The outputs above are low current outputs and must be used with a relay if the circuit's requirement

is more than 300 mA.

Pushbutton LED Programming Switch Assembly: (2 Pin Blue & 2 Pin White Connectors)

Route the gray and black wires in the 2 pin connector and the red and blue in the two pin connector from the previously

installed push-button LED programming switch assembly to the control module and plug these into the mating blue

and white connectors on the side of the module.

2 Pin Transponder Control Output: (Yellow Connector)

This output is intended to allow the control of a transponder bypass interface module or transponder

bypass relay. The system also allows software selections to control the way in which this output oper-

ates, see remote start feature # 10 for setting this output.

When the unit is selected for output during the start sequence, this output will be active at the same time

Ign. 3 becomes active, and will remain active until the vehicle has started. This will be used for one time

read transponder circuits.

When the unit is selected for transponder on, this output will become active at the same time ign. 3

becomes active, and will remain active all the time the unit is operational under the control of the remote

start. When the unit is selected for continuous and the vehicle is started via the Remote Start, this

output will become active at the same time ign. 3 becomes active and will remain active until the ignition

in the vehicle goes low. This will allow the unit to be used for continuous read transponders circuits.

128-8121

12 of 24

3 Pin Door Lock/Unlock Harness: (White Connector)

The Red and Green wires will provide either a pulsed ground output to the factory door lock control relay, or a

pulsed + 12 volt output to the factory door lock control relay. In either case, the maximum current draw through

these outputs must not exceed 300mA. The Red w/Black trace wire will provide a pulsed ground only, and will

only provide an output when the unlock button of the transmitter is pressed a second time after a first unlock

command was issued. This is used for second step unlock or all doors unlock in a two step circuit. In this

arrangement, Red is used to control the drivers door unlock relay, and the Red/Black will be used to control unlock

of all other doors.

3 Wire Ground Switched Door Lock Circuits:

In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence,

or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door

lock switch to the factory door lock relay.

The Green wire of the door lock harness provides a ground pulse during the disarming sequence, or pulsed

ground unlock output. Connect the Green wire to the low current ground signal wire from the factory door unlock

switch to the factory door unlock relay. See Below For Wiring Detail.

3 Wire Positive Switched Door Locks:

In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming

sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the

factory door unlock switch to the factory door unlock relay.

The Green wire of the door lock harness provides a + 12 volt pulse during the arming sequence, or pulsed 12 volt

lock output. Connect the Green wire to the low current 12 volt signal wire from the factory door lock switch to the

factory door lock relay. See Below For Wiring Detail.

3 Wire Ground Switched 2 Step Door Locks

In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output.

Connect the red wire to the wire that provides a low current ground signal from the factory door lock switch to the

factory door lock control relay.

The green wire provides the first ground pulse during disarming, or the drivers door pulsed ground unlock

output. Connect this wire to the drivers door unlock relay that requires a low current ground signal to unlock only

the drivers door. If the vehicle does not have a separate drivers door relay, one will have to be added. Locate the

drivers door unlock motor wire and cut it at a convenient location to allow wiring of an optional relay. Connect the

door side of the cut wire to terminal 30 of the optional relay added. Connect the vehicle side of the cut wire to

terminal 87a of the optional relay added. Connect the green wire of the 3 pin harness to terminal 86 of the optional

relay added. Connect terminal 85 of the optional relay added to a fused constant + 12 volt source.

128-8121

13 of 24

Most vehicles door lock/unlock motor legs rest at ground, and switch +12 volts to the door lock/unlock motor legs

for operation, if this is the case in the vehicle you are working on, connect the remaining terminal, 87, to a fused +

12 volt source. In the rare instance that the vehicle door lock/unlock motor legs rest at + 12 volts and switches

ground to the door lock/unlock motors, connect the remaining terminal, 87, to chassis ground.

The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second

time after disarming. Connect the Red/Black wire to the wire that provides a low current ground signal from the

factory door unlock switch to the factory door unlock control relay.

3 Wire Positive Switched 2 Step Door Locks

The green wire provides a positive pulse during arming, or the pulsed + 12 volt lock output. Connect the green

wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock

control relay.

The red wire provides a positive pulse during disarming, or the drivers door pulsed positive unlock output.

Connect this wire to the drivers door unlock relay that requires a low current positive signal to unlock only the

drivers door. If the vehicle does not have a separate drivers door relay, one will have to be added. Locate the drivers

door unlock motor wire and cut it at a convenient location to allow wiring of an optional relay. Connect the door side

of the cut wire to terminal 30 of the optional relay added. Connect the vehicle side of the cut wire to terminal 87a of

the optional relay added. Connect the red wire of the 3 pin harness to terminal 86 of the optional relay added.

Connect terminal 85 of the optional relay added to chassis ground. Most vehicles door lock/unlock motor legs rest

at ground, and switch +12 volts to the door lock/unlock motor legs for operation, if this is the case in the vehicle you

are working on, connect the remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle

door lock/unlock motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect he

remaining terminal, 87, to chassis ground.

The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second

time after disarming. Because the vehicle you are working on requires a positive pulse from the factory door lock

switch to the factory door lock control relay, you will have to add a relay to invert the output polarity of this wire.

Connect the Red/Black wire to terminal 86 of the optional added relay. Connect terminal 85 & 87 to a fuse + 12 volt

source. Connect terminal 30 to the low current door unlock wire from the factory door switch to the door unlock

control relay.

Note: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt

Door Lock Control Circuits

These applications require the use of additional components which may include relays, fixed resistors, or for

convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the

Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits.

128-8121

14 of 24

5PinAccessoryOutputHarness

Dark Blue Wire : Delayed 300 mA Pulsed Output/Channel 3

The dark blue wire pulses to ground via an independent RF channel from the keychain transmitter. This is

a transistorized, low current output, and should only be used to drive an external relay coil.

Thisoutputisactivatedbythesametransmitterbuttonthatisusedtoactivatetheremotestartfunction. Press

and hold the trunk/key button to activate this trunk release output, or press and release the trunk/key button

two times within 2 seconds to activate the remote starter.

WARNING:Connectingthedarkbluewiretothehighcurrentswitchedoutputofthetrunkreleasecircuitsand

some remote start trigger inputs, will damage the control module.

Connectthedarkbluewiretoterminal86oftheAS-9256relay(orequivalent30Aautomotiverelay),connect

terminal85toafused+12voltsourceandwiretheremainingrelaycontactstoperformtheselectedfunction

desired.

Channel 3 Relay Wiring Detail

From 2 Pin

Green w/ Black Trace Wire: 300mA Latched Channel 4 Output

The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiver is

accessed. Pressing the pre-programmed transmitter button(s) will access channel four and will remain

active, for up to 20 seconds, as long as the transmitter button(s) is held. This is a low current output and

must be connected to a relay to supply power to the device you intend to control. Connect Green w/ Black

Trace wire to terminal #86 of a VF45F11 P&B relay or equivalent. Connect terminal #85 of the relay to a

fused + 12 volt source. Connect the common, normally open, and normally closed contacts of the relay to

perform the selected function of the channel 4 output.

Note: This wire also can be used for defrost activation as dictated by the setting of feature # 1 of Bank 3.

Anytime the vehicle is running under control of the Remote Start and Channel 4 is activated, then

dependent on the selection of this feature, Green/Black will be activated as a pulse for 1 second, or

for 10 minutes. Note this wire will not operate when the vehicle is running under the power of the

ignition key, only while under the control of the remote start or if not used for defrost then an output

will occur as indicated above.

WARNING ! Connecting the Dark Green w/Black trace wire to any high current switched out-

put (300mA max.) will damage the control module.

Lt Blue/Green Wire : DELAYED 300 mA PULSED OUTPUT / CHANNEL 5

The light blue/green wire pulses to ground via an independent RF channel from the keychain transmitter.

This is a transistorized, low current output, and should only be used to drive an external relay coil.

WARNING: Connecting the light blue/green to the high current switched output of trunk release circuits,

some remote start trigger inputs, will damage the control module.

Connect the light blue/green to terminal 86 of theAS - 9256 relay (or equivalent 30Aautomotive relay) and

wire the remaining relay contacts to perform the selected function of channel 5.

Lt Blue/Black Wire : DELAYED 300 mA PULSED OUTPUT / CHANNEL 6

The light blue/green wire pulses to ground via an independent RF channel from the keychain transmitter.

This is a transistorized, low current output, and should only be used to drive an external relay coil.

WARNING: Connecting the light blue/black to the high current circuits, will damage the control module.

Connect the light blue/black to terminal 86 of theAS - 9256 relay (or equivalent 30Aautomotive relay) and

128-8121

15 of 24

wire the remaining relay contacts to perform the selected function of channel 6.

Blue/Red Wire : DELAYED 300 mA PULSED OUTPUT / CHANNEL 7

The light blue/red wire pulses to ground via an independent RF channel from the keychain transmitter. This is

a transistorized, low current output, and should only be used to drive an external relay coil.

WARNING: Connecting the light blue/red to the high current circuits, will damage the control module.

Connect the light blue/red to terminal 86 of theAS - 9256 relay (or equivalent 30Aautomotive relay) and wire

the remaining relay contacts to perform the selected function of channel 7.

3 Pin Input/Output Harness:

Dark Blue/Black Trace Wire: External Trigger Input

The Dark Blue/Black trace wire allows the remote start unit to be activated from an external source. The

intent of this wire is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar

device. When this wire receives a ground pulse, the unit will start the vehicle. Connect this wire to a ground

pulsed output from the controlling circuit.

Green w/ White Trace Wire: Entry Illumination Ground Output

This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to unlock the

doors . This wire should be connected to an external relay, and wired to the vehicles interior entry lighting

whenever the optional Interior Illumination circuit is desired. See below for relay wiring details.

Black w/ White Trace Wire: 300 mA Horn Output

The black w/ white trace wire is provided to beep the vehicle’s horn. This is a transistorized low current

output, and should only be connected to the low current ground output from the vehicle’s horn switch.

If the vehicle uses a + 12 VDC horn switch, then connect the black w/ white trace wire to terminal 86 of the

AS 9256 relay ( or an equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12

VDC battery source. Connect relay terminal 87 to the vehicle’s horn switch output, and connect relay termi-

nal 30 to a fused + 12 VDC battery source.

Entry Illumination Detail

3 Pin Antenna/Receiver Connector: (White Connector)

Plug the previously routed antenna connector from the antenna receiver assemble into the mating connector

of the control module. This connector supplies 12 volts, ground and RF data from the antenna receiver to the

remote start module. Be certain this connector is firmly seated making good contact to the control unit.

TIMEDSTARTPROGRAM:

TheRemoteStartunithastheabilitytostartthevehicleautomaticallyattimedintervals. Thisfeatureisuseful

inextremelycoldclimateswherestartingtheengineistheonlymeanstokeepthebatterychargedandfluids

warm. Theoperatorhastheoptiontohavetheunitstartevery2or4hoursforamaximumof48hours. Factory

preset is to start at 4 hour intervals. To select 2 or 4 hour automatic start timer:

1. Start By Holding the Pushbutton Switch On.

2. While Holding the Pushbutton Switch Turn The Ignition Switch On Then Off

3a) Within 10 seconds of turning the ignition switch off, Release and then Push On and release the Push-

button Switch 2 times holding it on the second time until the siren and or lights flash and chirp 2 times

indicating that the 2 Hour Start Interval has successfully been set. or

3b) Within 10 seconds of turning the ignition switch off, (Step 2) Release

and then Push On and release the Pushbutton Switch 4 times holding it on the fourth time until the siren

and or lights flash and chirp 4 times indicating that the 4 Hour Start Interval has successfully been set.

Note: Once selected, 2 or 4, this timer interval will remain in memory until it is manually changed. To

change, the above sequence will have to be followed.

128-8121

16 of 24

TIMEDSTARTOPERATION:

Tobeginthestarttimer, within10secondsofturningofftheignitionswitch, activatetheRFcommandtostart

2times.(Pressthetrunk/keybuttonfourtimes). Thelightswillflashandthesirenwillchirp4times.Indicating

timedintervalmodehasbeeninitiated.Thevehiclewillautomaticallystartevery2or4hoursasprogrammed.

To cancel the timed start mode start the vehicle either by RF or by the ignition key.

Programming Tach Rate:

Note: All applications require that tach be programmed.

The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote

start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been

learnedandstored. Ifthetachrateisnotproperlyprogrammedtothespecificvehicle,theunitmaynotrealize

that the vehicle is running in certain instances and could re-engage the starter motor.

The Remote Car Starter will learn the tach rate of most vehicles single ignition coils, multiple coil packs, and

or single injector. To learn tach;

1. Turn the ignition key to the ON position.

3. Press and release the program push-button switch 3 times.

4. Immediately turn the ignition key OFF.

5. Hold the program push-button switch ON, then start the vehicle using the ignition key.

6. When the unit senses the tach signal, the parking lights will begin to flash.

7. Release the program push-button switch. The parking lights will turn on for 3 seconds to indicate that the

tach signal is stored and the unit is now out of the program mode.

3.Diagnostics:

1. Be sure that programmable feature number #9 is set to the "Diagnostics On" mode.

2. Press and hold the program push-button switch on, then turn the ignition key to the "ON" position.

3. Thelightswillflashandthenumberofflasheswillindicatethereasonforshutdownonthelastremotestart

attempt. The indications are as follows.

1 Flash

5, 10, 15, or 20, minute run timer expired.

2Flashes Low or No tach signal received.

3Flashes Positive input shut down.

4Flashes Control switch was moved to "Off" position.

5Flashes RFShutdowncommandreceived.

6Flashes High RPM signal over speed shut down.

7Flashes TachhasNOTlearned.

8Flashes Negativeinputshutdown

Multi Coil Pack Adapter: (Optional)

The multi coil pack adapter, (P/N 136B1400), is designed for use with vehicles that do not respond to single

coil tach programming. Although the tach resolution of this circuit is designed to interface direct with most

vehicles, there may be an occasion where the following circuit may be required.

To use the adapter, the Green/Black wires must connect to the negative side of the ignition coil(s).

1. For vehicles utilizing independent coils per cylinder, connect the three Green/Black leads to alternate

coils. To achieve optimum performance the coil signals must be evenly distributed. This is accomplished

by first mapping out the firing order of the engine in groups of as indicated below. Draw a circle around

any of the columns. The Green/Black wires should be connected to the negative (-) terminal of the

respective cylinder number which appears in any of the circles.

2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil

pack. For 8 cylinder, four coil systems, connect to any of the three coils.

3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the

on and start position and have 0 volts with the ignition in the off position.

4. Connect the Green wire to the (Green) or (Orange/Green) tach input of theAudiovox remote start unit.

128-8121

17 of 24

TESTING YOUR INSTALLATION:

W A R N I N G ! ! The following procedure must be performed after the installation of anAudiovox Remote

Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the

unit in the following manner may result in personal injury, property damage, or both.

HOOD PIN SAFETY SHUT DOWN:

The intention of the hood pin safety shut down is to prevent the Remote Start unit from being activated while

a mechanic or vehicle owner is performing normal routine vehicle maintenance.

To test the integrity of this circuit:

1. With the driver's window in the down position, start the vehicle using the RF transmitter.

2. Reach inside the car and pull the hood release.

3. Raise the hood and confirm that the remote start unit shuts down.

If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of theAudiovox Remote

Start Unit.

WA R N I N G ! !

DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE

OPERATION OF THE HOOD PIN SAFETY SHUT DOWN FEATURE.

MANUAL SHUT DOWN / ENABLE CIRCUIT:

The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of the

Remote Start Unit regardless of the RF transmitter operation.

1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the PRLED on.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED begins to flash two short flashes followed by one long flashes and continues this pattern until

returned to normal mode of operation.

This puts the unit into the R/S Override mode indicating that the remote start is in the service mode and

will not start from RF or any other input Posse or otherwise.

To Exit R/S Override Mode

1) With the system disarmed, Press and Hold the PRLED on.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED turns off indicating that the R/S unit is fully functional one again.

WA R N I N G ! !

DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE

OPERATION OF THE MANUAL SHUT DOWN / ENABLE FEATURE.

NEUTRAL START SAFETY TEST:

The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any

position other than Park, or Neutral. When installing a Remote Start Device, it is imperative that the Yellow

Starter wire be connected to the ignition switch side of the Neutral Start Switch. Consideration for the

placement of a starter inhibit relay is important as well, and should be connected to the ignition switch side

of the Yellow Start Wire.

To test the integrity of the Neutral Start Safety Circuit:

1. Set the vehicle parking brake.

2. Block the drive wheels to prevent vehicle movement.

3. Temporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch.

4. Sitting in the vehicle, start the engine using the vehicle's ignition key.

5. Step on the brake pedal and shift the gear selector into reverse.

6. Allow the transmission to shift. When you feel the engine pull, do not move the gear selector just turn the

ignition switch off. DO NOT attempt to remove the key.

7. Keeping the brake pedal depressed, activate the RF transmitter in an attempt to start the vehicle. The car

should not start.

128-8121

18 of 24

8. Repeat the above test this time move the gear selector to the drive position. If the unit attempts to start,

failing this test, recheck your Yellow Wire's connection. This wire must be connected to the ignition switch

side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral

Safety Switch, it will be necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle.

The information concerning the Mechanical Neutral Safety Switch provided below will help you to deter-

mine if the vehicle you are working on has this type of safety switch and will provide alternate wiring

methods to accommodate this situation.

WA R N I N G ! !

REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY

DISCONNECTED IN STEP 3.

DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF

THE NEUTRALSAFETY START FEATURE.

MECHANICALNEUTRAL SAFETY SWITCH CONSIDERATIONS:

Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety

when installing a remote start device. Often when the ignition switch is turned off while the gear selector is

in any position other than park or neutral, the mechanical function will not allow the key to be turned to the

start position or be removed from the ignition cylinder. This configuration prevents mechanical operation while

the vehicle is in gear but offers no consideration for electrical operation. Because of this potential problem,

this installation requires the additional connection of a safety wire from the remote start device to the vehicle

Park/Neutral ECM Input or the vehicle key in sensor. This connection will prevent remote start operation if the

key is left in the ignition switch regardless of the gear selector position.

PARK / NEUTRAL ECM INPUT:

The Park / Neutral ECM input is the preferred method of installation. This not only maintains the integrity of

the factory circuit, it is also the easiest to install, providing the vehicle you are working on has this ECM input.

The installation required for this application (shown below), indicates the slight reconfiguration of the control

switch wiring and the addition of a 4000 series diode. Shown is a typical GM Park/Neutral ECM input circuit.

To connect the Audiovox remote start unit to the GM Park / Neutral ECM input:

1. Locate the Orange / Black reference wire in the "C2" connector found at the ECM in GM B Body vehicles

or, locate the equivalent reference wire in the vehicle you are installing theAudiovox Remote Start Unit in.

2. Connect the Cathode, (Striped) end, of a 4000 series diode to this reference wire.

3. Connect theAnode, (Non Striped) end, of the diode to one side of the Remote Start enable switch.

4. Connect the other side of the enable switch to the Black/White enable input wire of the Remote Start unit.

The reference diagram below shows a typical GM B Body ECM reference wire and how it is to be connected

to the Remote Start Unit.

KEY IN SENSOR CIRCUITS:

If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two

alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a

margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear.

AUDIOVOXADVISES THATYOU MAINTAIN THE FACTORYCIRCUITWHENEVER POSSIBLE. The follow-

ing two circuits may be used only if the above circuit is not available.

128-8121

19 of 24

Note: When completing an installation using either of the following key in sensor circuits, if the operator

inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle

will shut down. This must be explained to the operator as it is in contrast to the normal operation of

a vehicle utilizing an electrical neutral start switch and is inconsistent with the operator's manual.

Additional information concerning Key In Sensor methods 1 & 2 are listed below and should be reviewed

before considering either alternative.

Method 1 will allow the safety required for the remote start unit and prevent the vehicle from starting while

in any gear other than Park or Neutral while the key is in the ignition cylinder. However, if the key is left in

the ignition switch and the door is left opened, the added relay will be energized causing a 150mA drain on

the battery.

Method 2 will allow the safety required for the remote start unit and prevent the vehicle from starting while

in any gear other than Park or Neutral while the key is in the ignition cylinder. However, the original factory

key in chime module will not alert the owner that the key has been left in the ignition switch. In addition, this

may also effect other warning tones such as the light on reminder.

These situations should be carefully considered before altering the vehicle's wiring and must be fully ex-

plained to the consumer.

Circuits may be used only if the above circuit is not available.

METHOD 1

To connect to the key in sensor as shown in method 1:

A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.

B. Cut this wire and connect the ignition cylinder side to chassis ground.

C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .

D. Cut this wire and connect the ignition cylinder side to terminal #30 of a P&B VF45F11 or equivalent relay.

E. Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non

striped) side to the negative shut down safety wire (Gray / Black) of theAudiovox Remote Start Unit.

F. Connect terminal #86 of the relay to a fused +12 volt constant battery source.

G. Connect terminal #87 of the relay to the Chime Module side of the previously cut wire in step D.

H. Connect terminal #85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B.

Note: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down

circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non

Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode

(Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an

alarm trigger input, be certain to use the dual diode assembly packaged with theAudiovox Remote

Start Unit as shown following.

METHOD 2

To connect to the key in sensor circuit as shown for method 2:

A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.

B. Cut this wire and connect the ignition cylinder side to chassis ground.

128-8121

20 of 24

C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .

D. Cut this wire and connect the ignition cylinder side to the Remote Start Negative Safety Shut down Wire

Gray/Black, using a 4002 series diode as shown above.

Note: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down

circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non

Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode

(Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an

alarm trigger input, be certain to use the dual diode assembly packaged with the Audiovox Remote

Start Unit as shown in this installation guide.

AFTER THE CONNECTION OF THE NEUTRAL START SAFETY WIRE AS INDICATED IN ANY OF THE

PREVIOUSALTERNATE CONFIGURATIONS, THIS CIRCUIT MUST BE TESTED FOR OPERATION.

Retest by following the steps outlined in the NEUTRAL START SAFETY TEST shown in this manual.

4 Pin Upgrade Telematic Module:

Red = + 5 Volts

Black = Ground

White = Data TX

Yellow = Data RX

If used, connect the 4 pin harness from the Telematic one way module kit to the mating port on the controlling

circuit. NOTE: If using the TWO WAY Telematic module, only Ground, TX, and RX are used on this port, the

+ 12 volt supply for the two way module must be sourced separately or the unit will not operate.

4 Pin Upgrade Data Bus/Flash Logic Module:

If you are using an Audiovox Flash Logic module, it can be connected directly to the Alarm/Remote Start's

control module. Using the Blue 4 pin blue, red, black, & white harness and connect to the mating connector

on the Alarm/Remote Start control module. Wire the Flash Logic/Data Bus module to the vehicle as pre-

scribed in it's installation guide.

COMPLETING THE INSTALLATION:

After you have confirmed the operation of theAudiovox Remote Start unit and tested all the safety features of

the system:

1. If you have not done so already, place the red rubber handle cover over the handle of the control switch for

ease of identification. This will allow your customer to distinguish the Remote Start control switch from

the program switch.

2. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be

certain that the chosen mounting location will not inhibit any of the controls of the vehicle.

3. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in

contact with under the dash board or in the engine compartment areas.

CAUTION:Particularly avoid the area around the steering shaft and column, as wires can wrap around

these mechanisms and impair the safe operation of the vehicle.

4. Apply the Caution Labels supplied with this kit to a conspicuous area in the engine compartment. Make

sure to clean the surface before affixing the label.

5. Check the vehicle's wipers, lights, horn, etc.... to insure proper operation.

6. Replace all panels that were removed during installation, and retest the system.

7. Explain all activated features and safety systems associated with Remote Start Unit installed to the

customer.

128-8121

21 of 24

128-8121

22 of 24

THISPAGELEFTBLANKINTENTIONALLY

128-8121

23 of 24

128-8121

24 of 24

ACDelco Automobile Parts 26 SI User Manual
Acer Projector H7531D User Manual
Acer Tent AC701 User Manual
Agri Fab Lawn Sweeper 45 0352 User Manual
Aiwa Stereo Receiver AV D35 User Manual
Allied Telesis Switch AT 8000S 24 User Manual
American Dryer Corp Clothes Dryer AD 15 User Manual
Ask Proxima Projector C250 C250W C315 User Manual
Axis Communications Security Camera P3225 LV User Manual
Ayre Acoustics Stereo Amplifier AX 7E User Manual