RAVENNA™
SEMI-PEDESTAL SINK
VITREOUS CHINA
RAVENNA™ WALL-HUNG
SEMI-PEDESTAL LAVATORY
• Vitreous china
• Contemporary design wall-hung with
semi-pedestal P-trap cover for ease of cleaning
• Rear overflow
• Soap and accessory deck
• Optional with integral mounted towel bar
(ordered separately)
• Supplied with mounting kit
• Design matched to Ravenna toilets
(faucet shown not included)
• Faucet ledge with generous shelf area
for accessories
❏ 0268.444 Faucet holes on 4" (102mm) centers
(shown)
20"
(508mm)
FINISHED
WALL
3-1/4"
(83mm)
❏ 0268.888 Faucet holes on 8" (203mm) centers
❏ 0268.144 Center hole only
4"
(102mm)
7-3/4"
(197mm)
Nominal Dimensions:
24-1/4" x 19-1/2" x 34"
(616 x 495 x 864mm)
19-1/2"
(495mm)
SEMI-PED
BASE
1-3/4" DIA.
STD. DRAIN
OUTLET
Separate Components:
❏ 0268.004 Lavatory slab 4" (102mm) centers
❏ 0268.008 Lavatory slab 8" (203mm) centers
❏ 0268.001 Lavatory slab center hole only
❏ 0044.000 Semi-pedestal leg
TOWEL
RAIL
1/2" (13mm) DIA.
24-1/4"
SEMI-PED ANCHOR
SCREW HOLES ON
4-1/4" (108mm) CTRS
(616mm)
2"
(51mm)
9-1/2"
(241mm)
8-1/4"
(210mm)
Recommended Components:
❏ 3520.000 Integral Towel Bar
2-3/4"
(70mm)
002 Chrome, 295 Satin Nickel
7/8" (22mm) DIA.
SLAB ANCHOR
SCREW HOLES ON
9-1/2" (241mm) CTRS
SUPPLIES AS
REQUIRED
❏ 738520-0070A Towel Bar mounting kit
1-1/4" O.D.
WASTE
34"
(864mm)
1-1/4" O.D.
TAILPIECE
Bowl sizes:
19" (483mm) wide
12" (305mm) front to back
6" (152mm) deep
5"
*24-3/4"
(629mm)
*21"
(127mm)
(533mm)
14-3/8"
(365mm)
FINISHED
FLOOR
Compliance Certifications:
Meets or exceeds the following specifications:
• ASME A112.19.2 for vitreous china fixtures
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST
BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
❏ 1-1/4" Trap
* See faucet section for additional models available
© 2008 AS America Inc.
J60
Revised 5/06
|