®
Australian Top
Freezer
Refrigerator
Owner’s Manual
Keep these instructions for future reference. Be sure this
manual stays with refrigerator.
If your refrigerator requires ice maker water supply
connection, proceed to Connect Ice Maker Water Supply
section before leveling refrigerator.
• Remove end caps from top (some models) and
bottom of refrigerator door handle using a
screwdriver with blade covered in masking tape.
(See illustration following.) Remove one bottom
and two top handle screws to remove handle.
1. Plug in power cord.
2. Move refrigerator into final location.
3. Level refrigerator using a level placed on top of the
refrigerator.
End
cap
• Remove toe grille. Remove bottom hinge cover if
refrigerator has a stabilizing leg.
Handle
screws
• Turn 3/8" hex head roller adjustment screws to raise
or lower refrigerator cabinet. Front of refrigerator
must be 1/4" (6 mm), or 1/2 bubble on level, higher
than the back of refrigerator.
• Make sure refrigerator cabinet is level from side to
side by adjusting left and right roller adjustment
screw. Turn stabilizing leg (some models)
clockwise until firmly against floor.
or
End
cap
Roller adjustment
screw
• Models with automatically reversing logo.
Remove end cap from top of freezer handle using
a screwdriver with the blade covered with masking
tape. (See illustration below.) Remove one top and
two bottom mounting screws.
Stabilizing leg
(some models)
Bottom
hinge cover
• Handles with removable logo on handle.
Remove screw caps from handles using a
screwdriver with the blade covered in masking
tape. Remove handle screws to remove freezer
handle. Remove freezer handle cover by lifting
end. Bend tabs behind nameplate up and remove
nameplate. Rotate nameplate and cover.
Door Removal
Some installations may require door removal for
refrigerator to fit through door ways. If door removal is
required perform steps 2–5 of Door Reversal section to
remove doors. Perform steps 2–5 of Door Reversal
section in reverse order to replace doors.
Door Reversal
Handle with
removeable logo
Tools Required
End
Putty knife (blade covered with masking tape)
9/32" hex nut driver (some models)
3/8" hex nut driver
caps
Phillips screwdriver
Blade screwdriver
Some installations require door reversal to achieve full
door swing. To reverse door swing perform the following:
1. Remove and reverse refrigerator and freezer
handles performing the following steps:
Mounting
screws
IMPORTANT: For plug removal requiring use of flat
blade screwdriver or putty knife, blade of tool must be
covered with masking tape to avoid damage to
refrigerator finish. For plugs using a screwdriver- or
nut driver- style head, use appropriate tool to avoid
damage to plugs.
2. Remove top hinge cover. Top hinge cover snaps off.
Remove top hinge and shim using hex nut driver.
3. Lift freezer door off center hinge.
4. Lift door closure off center hinge pin. Remove center
hinge pin with a 5/16" or 9/32" hex nut driver.
3
5. Remove refrigerator door by lifting off bottom hinge.
6. Remove center hinge bracket and shim using
Phillips screwdriver.
1
8
/ " (3 mm)
7. Remove toe grille and bottom hinge cover. Both snap
off.
8. Remove bottom hinge and shim using hex nut driver.
Door
closure
5
16
/ " screws
Center hinge
pin
3
4
/ " (19 mm)
Phillips
screws
Center
hinge
Top
hinge
10. Remove plugs from side of refrigerator and freezer
doors using a putty knife with the blade covered in
masking tape.
Bottom
hinge
3
8"
/ screws
9. Reverse doors by performing the following steps:
• Replace bottom hinge and shim on opposite side
of cabinet.
Install button
plugs here
• Remove screws from center mullion. Place screws
in holes left when center hinge bracket was
removed. Rotate center hinge bracket 180° and
install center hinge bracket on opposite side of
cabinet with hinge screws. Reuse plastic hinge pin
washers.
Remove
button plugs
• Place refrigerator door on bottom hinge. Install
center hinge pin in center hinge bracket. Place
door closure on center hinge pin.
11. Mount freezer handle on opposite side of refrigerator
door using mounting screws previously removed.
Snap end cap(s) into place.
12. Mount refrigerator handle on opposite side of freezer
door using mounting screws previously removed.
Snap end cap(s) into place.
13. Replace plugs in empty side mounting holes on
refrigerator doors.
14. Proceed to Leveling Refrigerator procedures for final
placement of refrigerator.
• Remove plugs from top of refrigerator cabinet.
Replace plugs in holes left when top hinge was
removed. Remove hinge hole cover from freezer
door. Replace on opposite side of freezer door.
• Place freezer door on center hinge and door
closure. Install top hinge and shims on opposite
side of cabinet using hex nut driver. Snap hinge
cover in place on hinge.
• Use a penny at top to space door 3/4" (19 mm)
from cabinet. Make sure handle side of door is 1/8"
(3 mm) higher than hinge side of door before
tightening top hinge screws.
Connect Ice Maker Water Supply Line
CAUTION
!
To avoid property damage, protect soft vinyl or other
flooring with cardboard, rugs, or other protective
materials when moving refrigerator. Make sure
stabilizing leg is raised before moving refrigerator.
Raise stabilizing leg by turning counterclockwise.
4
1. Remove plastic cap from water valve inlet port.
CAUTION
!
Observe the following to avoid property damage:
• Confirm water pressure to water valve is between 20
and 100 pounds per square inch.
Water valve
inlet port
• Copper supply tubing must be routed where the
temperature is 55°F (13°C) or higher to prevent
freeze-ups.
• Start adaptor fitting and nuts by hand to avoid cross
threading. Tighten adaptor fitting and nuts with
pliers and wrenches. Do not overtighten.
• Check for water leaks and correct if necessary
before returning refrigerator to normal location, and
24 hours after connecting.
Plastic
cap
2. Place brass nut and brass sleeve on copper tubing.
(Brass nut and sleeve are found in literature packet.)
Insert copper tubing into water valve inlet port.
Connect brass nut on copper tubing to water valve
inlet port. Start connection by hand then use a 1/2"
(13 mm) open end wrench. Make sure copper tubing
is secure by pulling on copper tubing.
Important
• Before connecting water supply, contact a plumber to
connect copper tubing to household plumbing in
compliance with local codes and ordinances.
• DO NOT use self-piercing type or 3/16" saddle valves!
Both reduce water flow, develop sediment build-up
more rapidly, and may cause leaks if repair is
attempted. The correct type of shut-off valve requires
a 1/4" hole to be drilled on top or side (not bottom of
horizontal pipe) of water supply pipe prior to valve
attachment.
"P" clamp
Copper tubing
Brass sleeve
Water valve
Materials Required
1/4" O.D. (6 mm) flexible copper tubing. Length of copper
tubing must reach from water supply connection to water
valve inlet port on back of refrigerator plus an additional
8 ft. (2.5 m) of tubing for a service loop. A service loop
will allow refrigerator to be pulled away from the wall
without disconnecting tubing.
inlet port
Brass nut
3. Turn on water supply to refrigerator and check for
leaks. Correct any leaks at connection. Be careful
not to overtighten connection.
4. Create a service loop using extreme care to avoid
kinks. Secure copper tubing to refrigerator cabinet
with a “P” clamp.
5. Proceed to Leveling Refrigerator for final refrigerator
placement.
6. Review Installation Checklist in Owner’s Manual with
consumer.
5
Installation Checklist
This checklist is for personal records only.
Consumer Installer
Doors
Handles are solidly attached to doors.
Handle side of door is 3 mm (1/8") higher than hinge side. (Door lowers when
loaded with food.)
Doors seal completely to refrigerator cabinet.
Leveling
Refrigerator is tilted 6 mm (1/4") from front to rear.
Toe grille is properly attached to refrigerator.
Ice Maker
Water supply to refrigerator is turned on.
Water leaks are not present at connection between household water supply and
refrigerator. (After 24 hours, consumer should check connection for water
leaks.)
Ice maker arm is in on position for ice production. (It may take up to 24 hours
for first harvest of ice.)
Product Literature
Owner's manual is reviewed including the following information.
• product registration card
• Refrigerator and freezer controls
• Chiller Fresh™ system
• Garden Fresh™ crispers
• normal operating sounds
Notes
Installer's Company Name/Phone Number
Date
Installer's Signature
Consumer's Signature
6
Refrigerator Features
Controls
This refrigerator operates most efficiently at household
temperatures of 13°–43°C (55°–110°F).
CAUTION
!
To avoid property damage, confirm shelf is secure
before placing items on shelf.
Refrigerator and Freezer Controls
Refrigerator and freezer controls are located on center
divider between refrigerator and freezer sections.
Refrigerator Shelves
When freezer control is set to OFF, neither refrigerator
nor freezer sections will cool. Initially, set both controls to
4. Wait 24 hours for refrigerator and freezer sections to
reach desired temperatures. After 24 hours, adjust
controls, one number at a time, as desired. 1 is warmest
setting and 7 is coldest.
Models feature either glass or wire shelves. Shelves
adjust to meet individual storage needs.
CAUTION
!
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change.
Exterior Moisture Control
Exterior Moisture Control is located on center divider
between refrigerator and freezer sections.
In humid conditions, refrigerators form condensation
around doors. Special heaters in refrigerator cabinet
minimize condensation.
• Remove shelves by lifting front, releasing hooks
from metal track then pulling out.
• Replace shelves by inserting hooks into metal track
and lowering front.
Humidity depends on location of refrigerator. Set control
to ON if refrigerator is in a humid area or whenever
moisture is evident around doors. Set control to OFF if
refrigerator is in a less humid area. Setting can be
adjusted as conditions change.
Metal tracks
High quality steel is used in this refrigerator. However,
constant exposure to moisture may cause refrigerator
cabinet to rust. Set control to ON anytime condensation
forms on refrigerator cabinet.
Setting Controls
Set controls precisely with a household thermometer that
includes temperatures between -21° to 10°C (-5° to
50°F).
Chiller Fresh™ System
Chiller Fresh™ system features a drawer inside a sleeve.
Air circulates between drawer and sleeve. This systems
keeps food fresh longer and up to 3°C (5°F) colder than
refrigerator temperature.
Put thermometer snugly between frozen packages in
freezer section. Wait 5–8 hours. If freezer temperature is
not -18° to -16°C (0° to 2°F), adjust control, 1 number at
a time. Check again after 5–8 hours.
Chiller Fresh™ control is located below front shelf trim.
Control adjusts amount of air circulating around drawer.
Slide control to cold for normal refrigerator temperature
and to coldest for colder temperature. Ice crystals may
form on drawer or food on coldest setting. Cold air can
decrease refrigerator temperature. Refrigerator control
may need to be adjusted.
Put thermometer in a glass of water in middle of
refrigerator section. Wait 5–8 hours. If refrigerator
temperature is not 3° to 4°C (38° to 40°F) , adjust
control, 1 number at a time. Check again after 5–8
hours.
Chiller Fresh
coldest
temperature
cold
climate control
• Remove drawer by lifting and pulling out. Remove
shelf by lifting front, releasing hooks from metal track
then pulling out.
• Replace shelf by inserting hooks into metal track and
lowering front. Use slots 1 through 3 only. Replace
drawer by sliding in.
7
When moving Chiller Fresh™ system left or right, move
control, located on center back wall of refrigerator
section, to same side as system.
underneath then pulling out. *For doors hinged on
left, remove right crisper.
4. Remove support post at recess in bottom center of
refrigerator section.
5. Remove other crisper by sliding to opposite wall. Lift
front while supporting underneath then pull out.
6. Replace crispers and shelf by reversing steps 1–5.
Covered Storage Bucket
Storage bucket has a lid and removable egg tray. When
tray is removed, bucket will accept items such as a
standard egg carton, ice, etc.
Chiller Fresh
Position
Lid
Garden Fresh™ Crispers
Garden Fresh™ crispers keep produce fresh longer.
Wrap produce tightly. Do not wash produce before
placing in crispers. Excess moisture could cause
produce to spoil prematurely. Do not line crispers with
paper towels. Paper towels will retain moisture.
Egg tray
Storage bucket
Garden Fresh™ control is located below front shelf trim.
Control adjusts humidity in crispers. Slide control to high
for produce with leaves such as lettuce, spinach or
cabbage. Slide control to low for produce with skins such
as cauliflower, corn or tomatoes.
Dairy Center
Dairy center provides convenient storage for items such
as butter, cheese, etc.
• Remove dairy center by lifting door, pushing tabs
toward center and pulling out.
Remove shelf and crispers by completing the following
steps.
1. Open left* crisper. *For doors hinged on left, open
right crisper.
• Replace dairy center by sliding in until tabs lock into
place and lowering door.
CAUTION
!
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change.
Dairy center door
2. Remove shelf by gently pushing up from underneath.
Tilt one end up then pull out.
Crisper shelf
3. Remove left* crisper by lifting front while supporting
8
Freezer Features
Wire Shelf
• Remove wire shelf by tilting one end up and pulling
out.
• Replace wire shelf by tilting one end up and placing
end on ledge. Tilt other end down and place on ledge.
Door Buckets
Door buckets adjust to meet individual storage needs.
• Remove door buckets by pushing tabs toward center
and pulling out.
• Replace door buckets by sliding in until tabs lock
into place.
Door bucket
Tabs
Door Shelves
Reversible Utility Rack
• Remove door shelves by lifting ends and pulling out.
• Replace door shelves by placing shelf on glides and
sliding down.
Freezer utility rack provides extra storage for ice cube
trays or other items. Remove rack by completing the
following steps:
1. Locate hook of utility rack opposite of ball point joint.
Holding wire rack firmly with both hands, press
forward on hook with thumbs until utility rack
detatches and swings loose.
Pull out
here
2. Repeat pressure on the ball point hook until utility
rack snaps free.
Push up
here
W
s
i
r
e
h
e
l
f
H
o
o
k
s
U
t
i
l
i
t
y
r
a
c
k
9
Care and Cleaning
CAUTION
!
Adhesives
1. Remove glue residue by rubbing toothpaste into
adhesive with fingers until adhesive loosens.
2. Rinse surface with warm water. Dry surface with a
soft, clean cloth.
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before cleaning. After cleaning, connect
power.
Door Gaskets
1. Clean door gaskets every 3 months (or as required
to keep clean) according to General instructions.
2. Apply a light film of petroleum jelly to the hinge side
of door to keep gaskets pliable.
CAUTION
!
To avoid personal injury or property damage, read and
follow all cleaning product manufacturer's directions.
Condenser Coils
General
Clean condenser coil every 3 months to ensure
maximum performance of refrigerator. Accumulated dust
and lint may cause the following:
• reduced cooling performance
• increased energy usage
• premature part failure
1. Remove toe grille by holding ends and pulling
forward.
2. Clean front surface of condenser coil with a vacuum
cleaner hose nozzle.
3. Replace toe grille by inserting clips in holes and
snapping in.
1. Wash surfaces with 4 tablespoons baking soda
dissolved in 1 quart warm water and a soft, clean
cloth.
2. Rinse surfaces with warm water. Dry surfaces with a
soft, clean cloth.
• Do not use the following items:
- abrasive or harsh cleaners, ammonia, chlorine
bleach, etc.
- concentrated detergents or solvents
- metal scouring pads
These items can scratch, crack and discolor
surfaces.
CAUTION
• Do not place buckets, shelves, etc. in dishwasher.
!
Odor Removal
1. Remove all food and disconnect power to
refrigerator.
To avoid property damage, protect soft vinyl or other
flooring with cardboard, rugs, or other protective
material. Verify stabilizing leg is raised before moving
refrigerator. Raise stabilizing leg by turning
counterclockwise.
2. Clean all interior surfaces including ceiling, floor, and
walls according to General instructions. Pay special
attention to corners, crevices, and grooves. Include
all drawers, shelves, and gaskets.
3. Connect power to refrigerator and return food to
refrigerator. Wash and dry all bottles, containers and
jars. Wrap foods in tightly sealed containers to
prevent further odor. After 24 hours, check if odor
was eliminated.
4. Pull refrigerator away from wall. Run a vacuum
brush across condenser fan outlet grille on back
of refrigerator.
Glass Shelves
CAUTION
!
Complete the following steps if odor was not eliminated.
4. Complete steps 1–2.
5. Place Garden Fresh™ crispers on top shelf of
refrigerator section. Pack refrigerator and freezer
sections including doors with crumpled sheets of
black and white newspaper.
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change.
6. Place charcoal briquettes randomly throughout
newspaper.
7. Close doors and let stand 24–48 hours.
8. Remove charcoal briquettes and newspapers.
9. Complete steps 2–3.
Remove shelf by lifting front, releasing hooks from metal
track then pulling out. Place shelf on a towel. Allow shelf
to adjust to room temperature before cleaning.
Clean crevices by completing the following steps:
1. Dilute mild detergent and brush solution into crevices
using a plastic bristle brush. Let set for 5 minutes.
2. Spray warm water into crevices using faucet spray
attachment.
Contact Consumer Affairs Department if odor was still
not eliminated. Call 1-319-622-5511 outside U.S.A.
10
3. Dry shelf thoroughly and replace shelf by inserting
hooks into metal track and lowering front.
Energy Tips
This refrigerator is designed to be one of the most
energy efficient refrigerators available. Reduce energy
use by observing the following.
Light Bulbs
WARNING
!
• Operate in normal household temperatures of 13° to
43°C (55° to 110°F) away from heat sources and
direct sunlight.
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before replacing light bulb. After replacing
light bulb, connect power.
• Set refrigerator, freezer, and Chiller Fresh™ system
controls no colder than necessary.
• Keep freezer section full.
• Keep door gaskets clean and pliable. Replace gaskets
if worn.
• Keep condenser coils clean.
CAUTION
!
• Turn exterior moisture control ON when necessary.
To avoid personal injury or property damage, observe
the following:
• Allow light bulb to cool.
• Wear gloves when replacing light bulb.
Vacation Tips
Complete the following steps for short vacations.
1. Remove perishable foods. Warranty does not
cover food loss. Check warranty certificate for
specific coverage.
1. Remove light bulb cover by removing screw at back
center. Pull cover down. Replace bulb(s) with40-watt
appliance bulb(s).
2. If an ice maker is installed, move ice maker arm to
off position.
2. Replace light bulb cover by placing cover over light
bulb. Insert and tighten screw.
Complete the following steps for long vacations.
1. Empty refrigerator and freezer sections.
2. Unplug refrigerator.
L
i
g
h
t
b
u
l
b
3. Clean refrigerator and door gaskets according to
General instructions in Care and Cleaning section.
4. Prop doors open, so air can circulate inside.
5. If an ice maker is installed, turn water supply to
L
i
g
h
t
b
u
l
b
c
o
v
e
r
refrigerator off and move ice maker arm to off
position.
S
c
r
e
w
11
Normal Operating Sounds
This new refrigerator may be replacing a differently
designed, less efficient or smaller refrigerator. Today’s
refrigerators have new features and are more energy
efficient. As a result, certain sounds may be unfamiliar.
These sounds are normal and will soon become familiar.
These sounds also indicate refrigerator is operating and
performing as designed.
1
8
1. Freezer fan air rushes and whirs.
2
2. Sealed system (evaporator and heat exchanger)
refrigerant flow gurgles, pops or sounds like boiling
water.
7
3. Condenser fan air rushes and whirs.
4. Compressor has a high pitched hum or pulsating
sound.
5. Defrost timer sounds like an electric clock and
snaps in and out of defrost cycle.
6
5
6. Freezer control clicks when starting or stopping
compressor.
7. Defrost heater sizzles, hisses or pops.
8. Ice cubes from ice maker (some models) drop into
ice bucket.
3
4
Water valve (some models) buzzes when ice maker
fills with water. This occurs whether or not
refrigerator is connected to water supply. If
refrigerator is not connected to water supply, stop
sound by raising ice maker arm to off position. (Not
shown)
Foam insulation is very energy efficient and has
excellent insulating capabilities. However, foam
insulation is not as sound absorbent as
previously used fiberglass insulation. (Not shown)
2
12
Before Calling For Service
Refrigerator does not operate.
• Confirm freezer control is on.
Garden Fresh™ crispers or Chiller Fresh™ system does
not close freely.
• Confirm refrigerator is plugged in.
• Check fuse or circuit breaker. Plug in another item at
that wall outlet.
• Wait 40 minutes to see if refrigerator restarts. If
freezer control is on, lights work but 2 fans and
compressor are not operating, refrigerator may be in
defrost cycle.
• Check for a package which may prevent drawer from
closing properly.
• Confirm drawer is in proper position.
• Clean drawer channels with warm, soapy water.
Rinse and dry thoroughly.
• Apply a thin layer of petroleum jelly to drawer
channels.
• Confirm refrigerator is level.
Refrigerator still won’t operate.
Refrigerator has an odor.
• See Odor Removal instructions in Care and Cleaning
section.
• Unplug refrigerator. Transfer food to another unit
or place dry ice in freezer section to preserve food.
Warranty does not cover food loss. Check warranty
certificate for specific coverage.
Refrigerator or ice maker make unfamiliar sounds or
seems too loud.
• It may be normal. See Normal Operating Sounds
section.
Food temperature appears too warm.
• See above sections.
• Allow time for recently added warm food to reach
refrigerator or freezer temperature.
• Check gaskets for proper seal.
Ice maker is not producing ice.
• Confirm ice maker arm is down.
• Confirm household water supply is reaching water
valve.
• Confirm ice maker wiring harness is completely
inserted into proper holes.
• Clean condenser coils.
• Adjust refrigerator and/or freezer control.
• Confirm rear air grille is not blocked. Rear air grille is
located behind left Garden Fresh™ crisper.
• Check for kinks in copper or plastic tubing. Remove
kinks or replace tubing.
• Check electrical connections to water valve coil and
connector block on refrigerator cabinet.
• Confirm freezer section is operating at proper
temperature.
Chiller Fresh™ system temperature is too warm.
• Slide Chiller Fresh™ control to colder setting.
• Adjust freezer control to colder setting.
Food temperature is too cold.
• Clean condenser coils.
• Adjust refrigerator control.
• Adjust freezer control to warmer setting. Allow several
hours for temperature to adjust.
Ice cubes have an odor.
• See Odor Removal instructions in Care and Cleaning
section.
• Discard ice and clean ice bucket or trays more
frequently. Ice cubes are porous and absorb odors
easily.
Refrigerator runs too frequently.
• It may be normal to maintain constant temperature.
• Doors may have been opened frequently or for an
extended period of time.
• Allow time for recently added warm food to reach
refrigerator or freezer temperature.
• Clean condenser coils.
Ice cubes stick together or ‘shrink’.
• Empty ice cube bucket or trays more frequently. If
used infrequently, ice cubes may stick together or
shrink.
• Adjust freezer control.
• Check gaskets for proper seal.
Ice forms in inlet tube to ice maker.
• Check water pressure. Low water pressure will
cause valve to leak. Self-piercing valves cause low
water pressure. Amana recommends using a
saddle valve. Contact Kleenmaid for availability.
Do not use self-piercing valve. Amana is not
responsible for property damage due to improper
installation or water connection.
Water droplets form on inside of refrigerator.
• It is normal during high humidity periods or if doors
have been opened frequently.
Water droplets form on outside of refrigerator.
• Check door gaskets for proper seal.
• Turn exterior moisture control switch ON.
13
Warranty
For all appliances serviced in Australia, please refer to the following warranty:
AUSTRALIAN REFRIGERATION WARRANTY
5 YEAR PARTS AND LABOUR – TOTAL PRODUCT
DOMESTIC WARRANTY - FULL FIVE YEAR WARRANTY
In addition to all statutory rights which you, the Consumer, have under the relevant laws in respect of this appliance,
during the first five years of ownership as the original purchaser of this Kleenmaid appliance, we guarantee that any
fault caused by faulty material or workmanship becoming apparent will be rectified free of charge for parts and
labour, provided that all service is performed during normal working hours by Kleenmaid or their designated Agents.
Where the appliance is installed outside the normal servicing area of the above, the Purchaser must pay for the cost
of transporting the appliance to and from the Agent or the Agent’s travelling cost to and from the Purchaser’s home.
COMMERCIAL WARRANTY - ONE YEAR WARRANTY
When this appliance is installed in a commercial application, you, the Consumer, have under the relevant laws in respect
of this appliance, during your first one year of ownership as the original purchaser of the Kleenmaid appliance, we
guarantee that any fault caused by faulty material or workmanship becoming apparent, will be rectified free of charge for
parts and labour, provided that all service is performed during normal working hours by Kleenmaid or their designated
Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser must pay for the
cost of transporting the appliance to and from the Agent or the Agent’s travelling cost to and from the Purchaser’s home.
WHAT THESE WARRANTIES DO NOT COVER
We are not responsible for any damage or malfunction unless caused by a defect in material or workmanship. This
includes but is not limited to abuse, misuse, improper installation and transportation damage. We are not responsible for
any consequential damages from any malfunction.
WARRANTY DOES NOT COVER REPLACEMENT OF LIGHT GLOBES OR GLASS BREAKAGE DUE
TO IMPACT
In case of fractured glass do not use your appliance.
WARRANTY REGISTRATION
Please complete the enclosed warranty card and post it to us or phone our Customer Call Centre.
SERVICE ASSISTANCE
To assist you when phoning our Customer Call Centre number to arrange a service call please complete the following
details and have them ready when you call.
Model Number:
Date of purchase:
Date of installation:
Kleenmaid Store purchased from:
KLEENMAID CUSTOMER CALL CENTRE
CONTACT NUMBER
1 800 072 144
14
Warranty
For all appliances serviced outside of Australia, please refer to the following warranty:
Limited One Year Warranty
Limited Five Year Warranty on Compressor
First Year
Amana will provide a free replacement part, f.o.b. Amana, Iowa, U.S.A., for any part which is defective due to
workmanship or materials.
Second through Fifth Years
Amana will provide a free replacement part, f.o.b. Amana, Iowa, U.S.A., for any compressor which is defective due
to workmanship or materials.
Warranty Limitations
Owner's Responsibilities
•
•
Begins at date of original purchase.
Service must be performed by an authorized Amana
technician.
•
•
Provide proof of purchase (sales receipt).
Provide normal care and maintenance. Replace
owner replaceable items where directions appear
in Owner's Manual.
Make product reasonably accessible for service.
Pay premium service costs for service outside
technician's normal business hours.
Pay for service calls related to product installation
or usage.
Warranty Is Void If
•
•
•
•
Serial plate is defaced.
Product is used on a commercial, rental or leased
basis.
Product has defect or damage due to product
accident, alteration, connection to an improper
electrical supply, fire, flood, lightning, shipping and
handling, or other conditions beyond the control of
Amana.
•
•
In no event shall Amana be liable for incidental or
consequential damages including food loss*.
•
Product is improperly installed or used.
Any questions regarding the above or to locate an authorized servicer, contact appliance supplier or:
Amana Appliances, L.C.
2800 220th Trail
PO Box 8901
Amana, IA 52204-0001
USA
Telephone 1-319-622-5511
Facsimilie 1-319-622-2180
15
|