SPECIAL APPLICATION
MANUAL PART NUMBER: 400-0431-005
TP115-110
COMPUTER/COMPONENT VIDEO + AUDIO
TWISTED PAIR TRANSMITTER
USER’S GUIDE
SPECIAL APPLICATION
PRECAUTIONS / SAFETY WARNINGS
1
·
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
Please read this manual carefully before using your
TP115-110. Keep this manual handy for future
reference. These safety instructions are to ensure
the long life of your TP115-110 and to prevent fire
and shock hazards. Please read them carefully and
heed all warnings.
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
1.1 GENERAL
·
Qualified ALTINEX service personnel or their
authorized representatives must perform all
service.
1.2 INSTALLATION
·
To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the
TP115-110 in direct sunlight, near heaters or
heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can
harm internal components.
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
·
·
Handle the TP115-110 carefully. Dropping or
jarring can damage the unit.
Do not pull any cables that are attached to the
TP115-110.
1.3 CLEANING
·
Clean only with a dry cloth. Never use strong
detergents or solvents such as alcohol or
thinner. Do not use a wet cloth or water to clean
the unit. Do not open the unit to clean.
1.4 FCC NOTICE
·
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
400-0431-005
2
SPECIAL APPLICATION
ABOUT YOUR TP115-110
2
TECHNICAL SPECIFICATIONS
3
Specifications are subject to change.
TP115-110
COMPUTER/COMPONENT VIDEO +
AUDIO TO TWISTED PAIR (TP)
TRANSMITTER
FEATURES/
TP115-110
DESCRIPTION
GENERAL
Inputs
The TP115-110 provides transmission of computer
video and audio signals over Twisted Pair-type
(CAT-5) cable when used together with an
ALTINEX Twisted Pair receiver, such as the
TP115-111. Stereo audio input is received via the
3.5 mm jack and is converted to mono prior to
transmission over the CAT-5 cable. The TP115-110
is lightweight, streamlined, and easy to use.
RGBHV/YPbPr
Stereo Audio
Output
15-pin HD female
3.5mm female
Video + Audio
Compatibility
RJ-45 female
ALTINEX – Twisted Pair
Standard for TP Series
VGA through UXGA
Signal types
This unit offers video equalization for up to 400 ft
(122 m) and the signal detect feature shows when
a signal is present.
Signal resolutions
or 480p, 567p, 720p, 1080i
Table 1. TP115-110 General
The latest generation of Twisted Pair devices uses
an innovative, patented technology* developed by
ALTINEX. The new signal processing technology
allows transmitting and receiving fully equalized
computer video signals, stereo, and audio signals
over long distances. The maximum distance at full
UXGA resolution is 400 ft (122 m) between devices
and may reach up to 750 ft (230 m) at VGA
resolution.
MECHANICAL
TP115-110
Weight
1.0 lb (0.45 kg)
0.09” Aluminum,
Black Semi Gloss
4.58 in (116 mm)
Enclosure
Length
Width
3.50 in (89 mm)
0.96 in (24 mm)
10°C-50°C
Height
T° Operating
T° Maximum
Humidity
MTBF (calc.)
OPTIONS
75°C
A second RJ-45 connector may be added to drive
two TP receivers, or the input connectors may be
substituted for use with composite or S-Video
signals.
90% non-condensing
38,000 hrs
Table 2. TP115-110 Mechanical
ELECTRICAL
Input
TP115-110
Video Analog Signal
Video Sync Level
Audio Signal Level
Output
1.0 Vp-p max.
TTL
* US Patent 7,065,190
0 dBu
ALTINEX – Twisted Pair
Standard for TP Series
Video + Mono Audio
Power
9 VDC Power
3.6 W max.
Table 3. TP115-110 Electrical
400-0431-005
3
SPECIAL APPLICATION
PRODUCT DESCRIPTION
4
400-0431-005
4
SPECIAL APPLICATION
APPLICATION DIAGRAMS
DIAGRAM 1: TYPICAL SETUP
5
TP115-110
TP115-111
400-0431-005
5
SPECIAL APPLICATION
DIAGRAM 2: INTERNAL VIEW
SIGNAL
DETECT
POWER
SYNC
PROCESSING
HOR
H/W
EQ
VER
COMPUTER/
COMPONENT
PAIR 1
PAIR 3
PAIR 2
VIDEO
RED
15-PIN HD
BLUE
GREEN
TWISTED
PAIR
OUTPUT
PLUG AND PLAY
LEFT
AUDIO
STEREO
3.5mm
PAIR 4
RIGHT
9V, 1A
2.5mm
PS
400-0431-005
6
SPECIAL APPLICATION
INSTALLING YOUR TP115-110
6
OPERATION
7
Step 1. Determine the best location for the
TP115-110 and TP115-111. Where
possible, locate the TP115-110 as close
to the video source as possible and the
TP115-111 as close to the receiving
component as feasible.
The TP115-110 requires only one adjustment be
made for optimal performance. The adjustment is
video equalization for long cable lengths.
7.1 VIDEO EQUALIZATION
Video equalization is provided to fine-tune the
displayed image on the remote display.
Typically, the equalization will be set to near
minimum for short cable runs. Cable lengths up
to 400 ft (122 m) will require near maximum
equalization.
Step 2. Apply power to the TP115-110 using the
power adaptor provided. The Power LED
should be on and red.
Step 3. Connect the video source to the input of
the TP115-110 using a high-quality video
cable.
The equalization adjustment on the TP115-110
works together with the TP115-111 to provide
equalization for maximum cable lengths. For
example, for cable runs less than 50 ft (15 m),
both equalization settings may be set to near
minimum. Cable runs of 400 ft (122 m) will see
equalization settings at about the three-quarter
position.
Step 4. The Power LED should change from red
to green indicating a signal is present.
Step 5. Connect the audio input source to the
audio jack on the TP115-110.
Step 6. Run
a
CAT-5
cable
from
the
4TP OUTPUT of the TP115-110 to the
4TP INPUT on the TP115-111.
TROUBLESHOOTING GUIDE
8
We have carefully tested and have found no
problems in the supplied TP115-110. However, we
would like to offer suggestions for the following:
NOTE: Ensure good signal transmission
by routing the cable avoiding any
sharp angles, creases, or bends.
8.1 NO DISPLAY
Step 7. Connect the TP115-111 video and audio
outputs to their receiving devices.
Cause 1: The source has a problem.
NOTE: The L+, L- and GND outputs on
the TP115-111 terminal block
output contain the mono audio
output signal. The R+ and R-
pins are not used.
Solution: Check the source and make sure
there is a signal present and all
source connections are correct. If
the source is working and there is
still no display, see Cause 2.
Step 8. Apply power to the TP115-111 using the
power adaptor provided. The Power LED
should be on and red; green if a signal is
present.
Cause 2: The path has a problem.
Solution: Connect the transmitter directly to
the receiver using a short CAT-5
patch cable. If the image is good,
there is a problem with the cable.
Otherwise, see Cause 3.
Step 9. The units are now operational.
Cause 3: Cable connections are incorrect.
Solution: Make sure the cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no display present, see
Cause 4.
400-0431-005
7
SPECIAL APPLICATION
Cause 4: Video equalization required.
ALTINEX POLICIES
9
Solution: Adjust the VIDEO EQUALIZATION
on the TP115-110. Long cable runs
may require adjustment on both the
TP115-110 and TP115-111.
9.1 LIMITED WARRANTY/RETURN POLICIES
Please see the ALTINEX website at
www.altinex.com for details on warranty and
return policies.
In general, cable runs less then 50 ft
(15 m) require little or no video
equalization and should be set to
minimum. Cable runs up to 400 ft
(122 m) will require near maximum
equalization on both the transmitter
and receiver.
9.2 CONTACT INFORMATION
ALTINEX, Inc.
592 Apollo Street
Brea, CA 92821 USA
TEL: 714 990-2300
Cause 5: The display has a problem.
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
Solution: Make sure the display is powered
and is turned on. If there is still no
display, please call ALTINEX at
(714) 990-2300.
8.2 NO SOUND
Cause 1: The source has a problem.
Solution: Check the source and make sure
that there is a signal present and all
source connections are correct. If
the source is working and there is
still no sound, see Cause 2.
Cause 2: The volume is too low.
Solution: Increase the gain at the source
toward maximum. If there is still no
sound present, see Cause 3.
Cause 3: Cable connections are incorrect.
Solution: Make sure that cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no sound, see Cause 4.
Cause 4: The receiving device has
problem.
a
Solution: Make sure the receiving device is
powered and is turned on. If there is
still no sound, please call ALTINEX
at (714) 990-2300.
400-0431-005
8
|