Altec Lansing inMotion Max Portable Speaker
™
®
for iPhone and iPod
iMT702
User Guide
Safety Information
The lightning flash with arrowhead, within an equilateral triangle,
is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Caution: To prevent the risk of electric shock, do not remove cover
(or back). No user-serviceable parts inside. Refer servicing to
qualified service personnel.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
RechARGeAbLe bATTeRy
10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for the replacement of the obsolete outlet.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type. Do not expose to excessive heat such as sunshine, fire, or the like.
The battery used in this product must be properly recycled or disposed of. Instructions for removing the
battery can be found in the Getting Started section. Please contact your local recycling center for proper
battery handling and disposal instructions.
11. Protect the power cord from being walked on or pinched – particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
12. Do not install in an area that impedes the access to the power plug. Disconnecting the power plug is
the only way to completely remove power to the product and must be readily accessible at all times.
Rated voltage: 3.7V Capacity: 1800mAh Type: LC18650
cAUTION
13. Power source – Use only power supplies of the type specified in the operating instructions or
as marked on the appliance. If a separate power supply is included with this apparatus, do not
substitute with any other power supply – use only manufacturer-provided power supplies.
To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade exposure.
WARNING
14. Unplug this apparatus during lightning storms or when unused for long periods of time.
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped. For service, refer to qualified service personnel, return to the
dealer, or call the Altec Lansing service line for assistance.
IMPORTANT SAFeTy INSTRUcTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
16. For products that incorporate batteries, please refer to local regulations for proper battery disposal.
17. Only use attachments/accessories specified by the manufacturer.
4. Follow all instructions.
18.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
5. Do not use this apparatus near water – This apparatus shall not be exposed to dripping or splashing,
and no objects filled with liquids, such as vases, shall be placed on the apparatus.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. The
apparatus should not be situated on a bed, sofa, rug or similar surface that may block the ventilation
openings. The apparatus must not be placed in a built-in installation, such as a closed bookcase or
cabinet that may impede the flow of air through the ventilation openings. Ventilation should not be
impeded by covering the openings with items such as newspapers, tablecloths, curtains, etc.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. No naked flame sources, such as lighted candles, should be placed on the apparatus.
1
Contents
Welcome................................................................................................................................................................................................. ii
Safety Information..................................................................................................................................................................................1
Package Contents..................................................................................................................................................................................3
Getting Started.......................................................................................................................................................................................4
Placing and Removing Adapters for the iPhone and iPod.....................................................................................................................5
Speaker Features and Indicators ...........................................................................................................................................................6
Speaker Controls....................................................................................................................................................................................7
Enhanced Remote Features...................................................................................................................................................................9
Listening to Your iPhone or iPod..........................................................................................................................................................11
Charging your iPhone or iPod ..............................................................................................................................................................12
Listening to the FM Radio ....................................................................................................................................................................12
Listening to a Non-docking iPod or Other Portable Audio Device.......................................................................................................13
Maintaining Your Speaker System .......................................................................................................................................................13
Troubleshooting....................................................................................................................................................................................14
Warranty ...............................................................................................................................................................................................17
2
Package Contents
Altec Lansing inMotion Max speaker system
User Guide and
Quick Connect Instructions
Enhanced remote
Miscellaneous adapters
for iPhone and iPod
AC adapter
FM radio antenna
3
Getting Started
how to Install the Ac Adapter
how to Disconnect the Rechargeable battery
If you need to replace the lithium-ion battery, you will need to first remove it.
1
Connect the AC adapter cable plug
into the speaker system’s jack.
1
2
Unplug the speaker system from the wall outlet.
The jack is located on the back of the
system.
Remove the rechargeable battery compartment cover.
The battery compartment is located on the back of the speaker
system. Remove the 2 screws securing the cover in place. Then
remove the cover.
2
Plug the AC adapter into the wall
outlet.
3
Unplug the battery and remove it.
how to charge the Lithium-Ion battery
Your Altec Lansing inMotion Max speaker
system includes a rechargeable lithium-ion
battery. This battery should be fully charged
before initial use of the speaker system. A full charge will provide up to 3.5
hours of continuous playing time.
NOTe The lithium-ion battery must be properly recycled or disposed of.
Please contact your local recycling center for proper battery handling and
disposal instructions.
how to Install the enhanced Remote battery
When the battery icon on the LCD screen displays a single segment, you
should recharge the battery. When the battery icon starts flashing, the
speaker system is about to automatically shut down.
The enhanced remote battery (included) is not installed at the factory. To
install the battery, follow the steps below:
1
Pull out the battery holder.
1
Connect the speaker system to a wall outlet.
The battery door is located on the
lower end of the remote. Simply pull
the tab to open the battery holder.
See the How to Install the AC Adapter section. The battery icon on
the LCD screen will show the battery is charging.
2
Allow the battery to charge.
2
3
Position the battery (included) so it
sits in the battery holder correctly.
Charging time: Up to 3 hours for a full charge. When the battery is
fully recharged, the battery icon is shown as full.
Make sure the polarity (the + and – sides of the battery) is correct.
WARNING During the recharging process, it is typical for the battery
to become warm. To be safe, keep flammable materials away from the
speaker system.
Replace the battery door.
NOTe Please discard used batteries properly.
4
Placing and Removing Adapters for the iPhone and iPod
Your Altec Lansing inMotion Max speaker system includes removable
adapters for today’s popular iPhone and iPod models. These adapters
ensure that your iPhone and iPod properly fit in the speaker system’s dock.
As new iPhone and iPod models are introduced, new adapters will be made
available to customers. You may also use the adapters supplied with your
how to Place an Adapter
1
Select the correct adapter for your
iPhone or iPod.
Using the correct adapter ensures a
proper fit for your iPhone or iPod.
2
Gently press the iPhone or iPod
adapter into the dock.
Now you can carefully place your
iPhone or iPod into the dock.
NOTe Your iPhone or iPod cannot be in a
case or a “skin.”
how to Remove an Adapter
1
2
Remove your iPhone or iPod.
Grip the adapter and pull gently upward.
5
Speaker Features and Indicators
Expanded Sound Stage technology button
Track forward button
Track back button
Volume increase button
Volume decrease button
Source button
Power
on/off
button
FM antenna connector
AUX jack
LCD
display
AC adapter jack
Universal docking station for iPhone or iPod
6
Speaker Controls
Ensure the AC adapter is connected to the system and plugged into the wall. See the Getting Started
section for more information. Press the button.
Turn on your speaker system
Turn off your speaker system
Press the button. Whenever you are finished using your speaker system, please remember to turn it
and your iPhone, iPod or other MP3 player off to conserve electricity.
Change audio source
Turn up the volume
Turn down the volume
Press the
button to cycle through and select the audio source: iPod, FM radio or AUX.
Press the + button.
Press the – button.
Skip to the beginning of the current song on
your iPhone or iPod
In “iPod” mode, press the button.
In “iPod” mode, press and hold the button.
In “iPod” mode, press the button.
Rewind the currently playing track on your
iPhone or iPod
Skip to the beginning of the next song on
your iPhone or iPod
Fast-forward the currently playing track on
your iPod
In “iPod” mode, press and hold the button.
Tune radio stations
In “FM” mode, use the and buttons. See the Listening to the Radio section for additional information.
In “FM” mode, press and hold the or button. See the Listening to the Radio section for additional
information.
Scan radio stations
7
Speaker Controls
See the Listening to a Non-docking iPod or Other Portable Audio Device section for specific information
on using devices attached to your speaker system’s AUX jack.
Listen to a non-docking iPod or MP3 player
Activate Expanded Sound Stage (ESS)
Proprietary ESS technology widens the stereo image to fill a room with sound. Press the ESS button to
technology
activate it.
Press the and
displayed on the screen, press the button to reset all settings.
buttons simultaneously for a few seconds. Once the word “RESET ?” is
Reset all settings
Reset all settings (see above), and use the + and – buttons to select the region closest to you
(“REGION 1: USA,” “REGION 2: EUROPE,” “REGION 3: JAPAN WIDE,” or “REGION 4: JAPAN.”)
Then, press the button to save your selection.
Select FM Band region
8
Enhanced Remote Features
The enhanced remote lets you operate many functions of your Altec Lansing
inMotion Max speaker system:
Turn on your speaker system
Turn off your speaker system
Press the button.
Press the button.
Press the
Power on/off button
Source button
Volume increase
button
Volume decrease
button
button to cycle through
Change audio source
and select the audio source: iPod, FM radio
or AUX.
Track back button
Track forward button
Expanded Sound
Stage technology
button
Play/pause button
Turn up the volume
Press the + button.
Press the – button.
Turn down the volume
FM preset buttons
FM preset buttons
In “iPod” mode, press the
playing a selected track. Press the button
again to pause it.
button to begin
Play/Pause a song on your
iPhone or iPod
Skip to the beginning of the current
song on your iPhone or iPod
In “iPod” mode, press the button.
Rewind the currently playing
track on your iPhone or iPod
In “iPod” mode, press and hold the button.
In “iPod” mode, press the button.
Skip to the beginning of the next
song on your iPhone or iPod
Fast-forward the currently playing
track on your iPhone or iPod
In “iPod” mode, press and hold the button.
9
Enhanced Remote Features
Tune radio stations
In “FM” mode, use the or buttons. See the Listening to the Radio section for additional
information.
In “FM” mode, press and hold the or button. See the Listening to the Radio section for
additional information.
Seek radio stations
In “FM” mode, tune to the station you’d like to store, and then press and hold one of
the PRESET buttons (P1, P2, P3 or P4). See the Listening to the Radio section for more
information.
Store a radio station
In “FM” mode, press the PRESET button (P1, P2, P3 or P4) that corresponds to the station
you’d like to hear. See the Listening to the Radio section for more information.
Select a preset radio station
Proprietary ESS technology widens the stereo image to fill a room with sound. Press the ESS
button to activate it.
Activate Expanded Sound Stage (ESS) technology
NOTe For best results, aim the enhanced remote control toward the inMotion Max speaker system.
10
Listening to Your iPhone or iPod
how to Access Additional Features on your iPhone or iPod Using
the enhanced Remote
1
2
Dock your iPhone or iPod in the Altec Lansing inMotion Max
speaker system.
Select “iPod” mode.
Press the P1 button once on the
Press the
button on your speaker system or enhanced
enhanced remote to advance to the next
shuffle mode. SH ALBU is displayed when
the system is in album shuffle mode. SH
remote until the iPod icon appears on the LCD.
3
4
5
Press the button on your iPhone or iPod.
SONG is displayed when the system is in
song shuffle mode. SH OFF is displayed
Music from your iPhone or iPod will start playing. The speaker
system and its remote are capable of controlling basic functions of
3rd-generation iPod models, the iPod touch and iPhone.
Shuffle function
when the shuffling function has been
turned off. Note: Use the P2 button on
some older iPod models. Functionality
may vary per iPhone or iPod model.
Adjust the volume.
Use the + and – buttons on the Altec Lansing speaker system
to adjust the system volume. Or, use the + and – buttons on the
enhanced remote.
Press the P2 button once on the
enhanced remote to advance to the next
repeat mode. RPT ONE is displayed when
the system is in the repeat one mode.
Find your desired song.
Press the or button on your speaker system or enhanced remote
to go to the next or previous track. Press and hold the or button
on your speaker system or enhanced remote while track is playing for
high-speed forward or reverse music search of the current track.
RPT ALL is displayed when the system is
the repeat all mode. RPT OFF is displayed
Repeat function
when the repeat function has been turned
off. Note: Use the P2 button on some
older iPod models. Functionality may vary
per iPhone or iPod model.
NOTe To conserve battery power, reduce the speaker system volume level.
NOTe During battery-only operation, the speaker system automatically shuts
down if no audio is detected for a few minutes. Press the button to turn the
speaker system back on. (If the speaker system is connected to a wall outlet,
it will remain on until the button is pressed and the indicator light shuts off.)
Press the P3 button on the enhanced
Access the previous playlist
remote.
NOTe The speaker system is compatible with the alarm clock and sleep
timer features built into select iPhone and iPod models. For these features to
work properly, the speaker system must be connected to a wall outlet. See
the user guide for iPhone or iPod for details on how to access these features.
Press the P4 button on the enhanced
Access the next playlist
remote.
11
Charging Your iPhone or iPod
Whenever your iPhone or iPod is docked and your Altec Lansing inMotion
Max speaker system is plugged into an AC outlet, your iPhone or iPod is
charging (until fully charged) – even if the speaker system is switched off.
how to Store Preset Stations
Your Altec Lansing speaker system’s enhanced remote enables you to
program up to 4 FM station presets:
1
2
3
Tune to the station you wish to store.
Listening to the FM Radio
While in “FM” mode, use the and buttons on your speaker
system or enhanced remote to tune to the desired station.
1
Plug the FM radio antenna into the
speaker system’s FM ANTENNA
jack.
Store the station.
Press and hold the P1, P2, P3 or P4 button on the enhanced remote
for a few seconds. You can store one FM station in each preset.
The jack is located on the back of the
system.
To store other stations, repeat the above steps.
2
Extend the FM antenna wire fully
for best FM reception. Also, do
not strip, alter or attach to other
antennas.
how to Recall Preset Stations
1
2
3
Make sure you are in “FM” mode.
If you’re not in “FM” mode, press the
speaker system or enhanced remote until the
button on your
appears on the LCD.
3
4
Select “FM” mode.
Press the
remote until the
button on your speaker system or enhanced
appears on the LCD.
Press a PRESET button (P1, P2, P3 or P4) on the enhanced
remote.
The radio will tune to your preset station.
Tune to the station you want to listen to.
Use the and buttons on your speaker system or enhanced
remote to tune in the desired station. Press and hold these same
buttons to find the next clear FM station.
Adjust the volume.
Use the + and – buttons on the Altec Lansing speaker system
to adjust the system volume. Or, use the + and – buttons on the
enhanced remote.
5
Adjust the volume.
Use the + and – buttons on the Altec Lansing speaker system
to adjust the system volume. Or, use the + and – buttons on the
enhanced remote.
12
Listening to a Non-docking iPod
or Other Portable Audio Device
Maintaining Your Speaker System
Place your speaker system on a level surface away from sources of direct
sunlight or excessive heat.
If you have a non-iPod MP3 player or other non-docking portable audio
device, you can enjoy it through your Altec Lansing inMotion Max speaker
system as well. Just connect it via the AUX jack. Here’s how:
Protect your furniture with a cloth or other protective material when placing
your speaker system on a natural wood or lacquered finish.
1
2
Locate a 3.5 mm stereo cable
(not included).
Clean your speaker system with a soft cloth moistened only with mild soap
and water. Stronger cleaning agents, such as benzene, thinner or similar
materials, can damage the surface of the unit.
Plug one end of the stereo cable
into your device.
Your device should have either a
headphone or LINE OUT jack for you
to plug into.
3
4
Plug the other end of the stereo
cable into your speaker system’s
AUX jack.
The AUX jack is located on the back of the unit.
Select “AUX” mode.
Press the
button on your speaker system or the enhanced
remote until the AUX icon appears on the speaker system’s LCD.
5
6
Turn on your device and start it playing.
Adjust the volume.
Use the + and – buttons on the speaker system to adjust the volume.
Or, use the + and – buttons on the enhanced remote.
NOTe You may need to adjust the device volume also. Your device’s
volume should be set to approximately ¾ volume.
7
When you are finished listening to your portable audio device,
please remember to turn both it and your speaker system off
to conserve electricity.
13
Troubleshooting
Symptom
Possible Problem
Solution
AC adapter isn’t plugged into a wall outlet
or the connector isn’t plugged into the
power supply jack on the back of the
speaker system
Plug the AC adapter into a wall outlet and plug the connector into the power
supply jack on the back of the speaker system.
Speaker system doesn’t
respond (no power)
Wall outlet is not functioning
Plug another device into the same outlet to confirm the outlet is working.
The rechargeable battery isn’t charged.
The power isn’t turned on.
Recharge the battery. (See the Getting Started section for details.)
Turn on the speaker system by pressing the button. The indicator light
turns on.
Using the wrong adapter for iPhone or
iPod or no adapter
Make sure the adapter is the proper fit for your iPhone or iPod.
iPhone or iPod doesn’t dock
properly
iPhone or iPod didn’t install properly
iPhone or iPod is not installed properly
Your iPhone or iPod software is too old
iPhone or iPod is locked up
Remove your iPhone or iPod from the dock and check for obstruction on the
connectors in the dock and on your iPhone or iPod. Then reseat it in the dock.
Remove your iPhone or iPod from the dock and check for obstructions on
the connectors in the dock and on your iPod. Then reseat it in the dock.
Upgrade software on your iPhone or iPod. For details visit
iPhone or iPod doesn’t
respond to the speaker
system
Please make sure your iPhone or iPod is working properly before docking into
the unit. Please refer to your iPhone or iPod manual for details.
Using 1st- or 2nd-generation iPod, iPod
Your speaker system cannot control those iPods or other devices.
shuffle or other devices
14
Troubleshooting
Symptom
Possible Problem
Solution
iPhone or iPod is not installed properly
Remove your iPhone or iPod from the dock and check for obstructions on the
connectors in the dock and on your iPhone or iPod. Then reseat it in the dock.
iPhone or iPod is locked up
Please make sure your iPhone or iPod is working properly before docking into
the unit. Please refer to your iPhone or iPod manual for details.
iPhone or iPod didn’t charge
AC adapter isn’t plugged into a wall outlet, Plug the AC adapter into a wall outlet and plug the connector into the supply
or the connector is not plugged into the
power supply jack on the back of the
speaker system
jack on the speaker system.
Volume level is set too high
Decrease the volume.
Sound source is distorted
If the iPhone or iPod original sound source (MP3) is of poor quality, distortion
and noise are easily noticed with high-power speakers. Try a different audio
source such as a music CD.
Sound is distorted
Battery is weak
Replace current battery with a new battery.
Enhanced remote doesn’t
work
Enhanced remote is not pointed toward
the speaker system
Point the enhanced remote toward the Altec Lansing speaker system and
move within 10 feet of the unit.
No sound from the AUX
device, such as an MP3
player or CD player
Volume on the device is set too low
Increase the volume on the device to approximately ¾ full volume.
Source selector is not set to AUX
Set source selector to AUX.
connected to the AUX jack
15
Troubleshooting
Symptom
Possible Problem
Solution
Static electricity, momentary interruption of 1. Disconnect the AC adapter cable plug from the speaker system’s jack.
The speaker system exhibits
erratic or unexpected
behavior. Controls do not
function.
power or abnormal operating conditions
may be responsible.
2. Close the stand on the back of the speaker system.
3. Wait 20–30 seconds.
4. Open the stand on the back of the speaker system.
5. Reconnect the AC adapter cable plug to the speaker system’s jack.
16
Warranty
ALTec LANSING ONe-yeAR LIMITeD WARRANTy
What Does the Warranty cover?
DISPOSAL OF OLD eLecTRIcAL AND eLecTRONIc eqUIPMeNT
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city office or your
household waste disposal service.
Altec Lansing warrants that its products shall be free from defects in materials or workmanship, with the
exceptions stated below.
What Is the Period of coverage?
This warranty runs for one year from the date of purchase. The term of any warranties implied by law shall
expire when your limited warranty expires. Some states and/or Member States in the European Union do
not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
What Does the Warranty Not cover?
This warranty does not cover any defect, malfunction or failure that occurs as a result of: improper
installation; misuse or failure to follow the product directions; abuse; or use with improper, unintended
or faulty equipment. (For information on proper installation, operation and use consult the manual
supplied with the product. If you require a replacement manual, you may download a manual from
www.alteclansing.com.) Also, consequential and incidental damages are not recoverable under this
warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
What Will Altec Lansing Do to correct the Problem?
Altec Lansing will, at its option, repair or replace any product that proves to be defective in material or
workmanship. If your product is no longer being manufactured, or is out of stock, at its option, Altec
Lansing may replace your product with a similar or better Altec Lansing product.
how to Get Warranty Service
To get a covered product repaired or replaced, you must contact Altec Lansing during the warranty
email address, telephone number, date of purchase and a complete description of the problem you
are experiencing. In the United States, you may alternatively contact Altec Lansing by telephone at
1-800-ALTEC88. Please be prepared to provide the same information. If the problem appears to be
related to a defect in material or workmanship, Altec Lansing will provide you a return authorization and
instructions for return shipment. Return shipments shall be at the customer’s expense, and the return
must be accompanied by the original proof of purchase. You should insure the shipment as appropriate
because you are responsible for the product until it arrives at Altec Lansing.
how Will State Law Affect your Rights?
This warranty gives you specific legal rights, and you may also have other rights, which vary from state
to state. Please note that in the European Union, you as a consumer might have other legal rights under
national legislation of European Union Member States governing the sale of Altec Lansing’s goods. Those
rights are not affected by this guarantee.
The above limited warranties and remedies are sole warranties and remedies available to purchaser, if, and
to the extent, valid and enforceable under the applicable law.
17
heADqUARTeRS 535 Rte. 6 & 209, Milford, PA 18337-0277 • 800-ALTEC-88. 570-296-4434. • Fax 570-296-6887
eUROPe 13 Rue Beaumont, L-1219 Luxembourg, Luxembourg
ASIA/PAcIFIc 23/F, Office Tower, Shun Hing Square Diwang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen, China 518008
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance
standards.
“Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple
performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Patents pending.
©2008 Plantronics, Inc. All rights reserved.
ALTEC, ALTEC LANSING, the Altec Lansing logo, the horn design, inMotion, and iMT702 are trademarks or registered trademarks of Altec Lansing, a division of Plantronics, Inc.
Plantronics, the logo design, and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc.
iPod is a trademark of Apple, Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple, Inc.
All other trademarks appearing herein are the property of their respective owners.
Designed by Altec Lansing in the USA. Made in China.
A12896 R04
|