AT-8600 Series Switch
Installation and Safety Guide
AT-8624T/2M
AT-8624PoE
AT-8648T/2SP
AT-8600 Series
Installation & Safety Guide
AT-8624T/2M
AT-8624PoE
AT-8648T/2SP
Download the complete document set from
2
AT-8600 Series Switch
AT-8600 Installation & Safety Guide
Document Number C613-000083 REV H
© 2006-2011 Allied Telesis Inc. All rights reserved. No part of this publication
may be reproduced without prior written permission from Allied Telesis Inc.
Allied Telesis Inc. reserves the right to change specifications and other
information in this document without prior written notice. The information
provided herein is subject to change without notice. In no event shall Allied
Telesis Inc. be liable for any incidental, special, indirect, or consequential
damages whatsoever, including but not limited to lost profits, arising out of or
related to this manual or the information contained herein, even if Allied Telesis
Inc. has been advised of, known, or should have known, the possibility of such
damages.
All company names, logos, and product designs that are trademarks or
registered trademarks are the property of their respective owners.
Installation & Safety Guide
Models Covered by this Guide ...................................................................................... 4
Package Contents ............................................................................................................. 4
Selecting a Site ................................................................................................................... 5
Installing the Switch ......................................................................................................... 6
Connecting the Switch .................................................................................................. 10
Checking LEDs ................................................................................................................ 13
Obtaining Documentation and Resources ............................................................... 18
Standards .......................................................................................................................... 19
Safety ................................................................................................................................. 20
Sicherheit .......................................................................................................................... 21
Sikkerhed .......................................................................................................................... 23
Veiligheid ........................................................................................................................... 24
Sécurité ............................................................................................................................. 25
Turvallisuus ....................................................................................................................... 26
Norme di Sicurezza ........................................................................................................ 28
Sikkerhet ........................................................................................................................... 29
Segurança .......................................................................................................................... 30
Seguridad .......................................................................................................................... 32
Säkerhet ............................................................................................................................ 33
4
AT-8600 Series Switch
Models Covered by this Guide
This document includes information about the following switches:
■
■
■
AT-8624T/2M 24-port 10BASE-T/100BASE-TX
AT-8624PoE 24-port 10BASE-T/100BASE-TX
AT-8648T/2SP 48-port 10BASE-T/100BASE-TX
Package Contents
The following items are shipped with each switch. Contact your authorised
distributor or reseller if any are damaged or missing.
■
■
■
■
■
One AC power cord
One power cord retaining clip
One serial cable for connecting the switch to a terminal or PC
One 19-inch rack-mount kit
One AT-8600 Series Installation & Safety Guide (which includes statutory and
safety information)
■
One warranty card
Preinstalled AT-A65 expansion modules
You can order the AT-8624T/2M or AT-8624PoE switches with two AT-A65
expansion modules included. These will already be installed in the expansion
bays of the switch.
For technical specifications for the AT-A65 expansion module, see the AT-A65
Expansion Module Installation and Safety Guide available from
Installation & Safety Guide
5
Selecting a Site
Before you install the switch, review the following considerations about its
location.
■
The switch requires an ambient temperature range of 0 º C to 40º C
(32º F to 104º F).
■
■
■
■
There should be adequate airflow around the switch and its vents.
The site should be dust-free and without moisture.
Humidity can be from 5% to 80% non-condensing.
You need a reliable and earthed (grounded) power supply source, preferably
dedicated and filtered.
■
Cabling must not be exposed to sources of electrical noise, such as radio
transmitters, broadband amplifiers, power lines, electric motors, and
fluorescent fixtures.
■
■
Switch ports are suitable for connection to intra-building or non-exposed
cabling is required.
Related network devices can be connected to the switch but cannot exceed
maximum cable lengths specified in the Hardware Reference.
■
■
You may need to remove cabinet doors to accommodate cords and cables.
Ensure easy access to the switch’s power and cable connections.
6
AT-8600 Series Switch
Installing the Switch
Ports on the switch are suitable only for connections within buildings (intra-
building) and with cables unexposed to the outside.
Before you begin
■
Read the safety information.
For your well-being and that of the equipment, read the safety information in
this document. You can also download this document from the
■
■
Verify the package contents if you have not already done so.
See “Package Contents” on page 4. If any items are damaged or missing,
contact your authorised distributor or reseller.
Gather necessary tools and equipment:
• Phillips #2 screwdriver to loosen the blanking plate, if any
• 4 sets of rack-mount screws and nuts, and a suitable screwdriver
To install a DC version of the PSU, you need an appropriate DC power
source, DC supply cable, ring connectors, and a crimp tool.
■
■
Choose a suitable operating location.
You can install the switch either in a 19-inch rack, on a flat bench, or against
a wall. Follow the guidelines in “Selecting a Site” on page 5 to choose a
location.
To ensure rack-mounted installations are earthed for compatibility with
Network Equipment Building System (NEBS), do the following:
•
Remove non-conductive coatings, such as lacquer and enamel, from the
rack rail where hardware will contact it. Also remove coatings from
unplated connectors, braided strap, and bus bars, and bring them to a
bright finish. Then coat them with an antioxidant before connecting
them. During installation, thread-forming screws with star washers may
be used for this purpose
•
All bare conductors must be coated with an appropriate antioxidant
compound before making crimp connections.
Warning Both AC and DC versions of this equipment must be earthed through
the power cables provided.
Installation & Safety Guide
Procedure
7
1. If you have any optional expansion modules, install them first.
The AT-8600 Series switches support the AT-A45/xx, AT-A46, AT-A47, and
AT-A65 expansion modules. Install them by following the instructions in the
relevant guide:
•
AT-A65 Expansion Module Installation and Safety Guide for the AT-A65
module only.
•
AT-A45/xx Series, AT-A46, and AT-A47 Expansion Modules Installation Guide
for the other expansion modules.
These instructions ship with individual expansion modules, and are also
Note that if you insert or remove a module when the switch is already
powered on, you must restart the switch before you can use the module.
2. Place the switch in its operating location.
If installing the switch in a rack:
•
Remove the rubber feet on the bottom of the switch with a flat-head
screwdriver.
•
Attach the two rack-mounting brackets to the switch with the screws
provided in the rack-mount kit.
3. Mount the switch in the rack using rack-mount screws
Note that the screws are not provided with the switch.
4. Install any SFPs.
You can install optional SFP (Small Form-factor Pluggable) modules into the
AT-8648T/2SP.
Warning Do not look into the optical ports of SFP cables or transceivers.
Invisible laser radiation may be emitted from disconnected fibres or
connectors.
In both SFP ports, the SFP transceivers must be inserted with the release
lever hinge at the bottom. Use the following figure as a guide.
8
AT-8600 Series Switch
.
release lever
hinge
AT-8600_sfp_shaded
Slide the transceiver into the SFP socket, and firmly press it until it engages.
To remove it, first release it by gently pulling the release lever, and then pull
it out of the socket. Never force a transceiver into or out of a socket.
When an SFP is installed into one of the two SFP ports, that SFP port takes
precedence over its corresponding 10/100/1000T port. When the SFP is
removed, the 10/100/1000T port is once again active.
5. Check the supply voltage and the switch’s rated voltage
AT-8600 Series switches are fitted with a universal main power supply that
functions from100–240 VAC and 50–60 Hz.
Specific power supply requirements for the model are on the rear or
underside of the switch. If the supply is outside the acceptable range, the
switch may not operate or may be damaged.
6. Apply AC power to the switch.
Plug the power cord into the AC power connector. This is on the switch’s
rear panel, as shown in the below figures.
Figure 1: AT-8624T/2M front and rear panel with AC power inlet
AT-8624T/2M
Layer
3
Fast Ethernet Switch
1
3
5
7
9
11
13
15
17
19
21
23
MODE
RS-232
TERMINAL PORT
STATUS
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
COL
100
LINK
MODE
LINK
FAULT
MASTER
RPS
25
26
FULL
ACT
MODE
PWR
10
2
4
6
8
10
12
14
16
18
20
22
24
Installation & Safety Guide
9
Figure 2: AT-8624PoE front and rear panel with AC power inlet
AT-8624POE
Layer
3
Fast Ethernet Switch
STATUS
1
3
5
7
9
11
13
15
17
19
21
23
100 LINK
FULL DUP
PD ON
ACT
10 LINK
HALF DUP
PD ERR
ACT
COL
MAX CURRENT
MODE
RS-232
TERMINAL PORT
1
3
5
6
7
8
9
11 13 15 17 19 21 23
FAULT
MASTER
RPS
25
26
PWR
2
4
10 12 14 16 18 20 22 24
2
4
6
8
10
12
14
16
18
20
22
24
Figure 3: AT-8648T/2SP front and rear panel with AC power inlet
LINK
49R MODE
CLASS
1
LASER PRODUCT
AT-8648T/2SP
Layer
3
Fast Ethernet Switch
DO NOT STARE
49
INTO BEAM
LINK
STATUS
COL
FLT
SFP
50
LINK
SPD
FDX
ACT
MSTR
RPS
PWR
LINK
50R MODE
MODE
7. Check that the PWR LED on the switch’s front panel is green.
If the PWR (power) LED fails to light, refer to the AT-8600 Series Hardware
Reference for troubleshooting information.
8. Connect the data cables.
Make sure each cable connection is secure. The switch can now process
basic Layer 2 switching functions.
10
AT-8600 Series Switch
Connecting the Switch
Some configuration is necessary to enable the switch’s advanced switching
capabilities. This is achieved via the Command Line Interface (CLI). On the
AT-8624T/2M, you can also use the Graphical User Interface (GUI).
Using the CLI to configure a switch
1. Connect a terminal or PC to the terminal port (ASYN0).
Using the supplied RS-232 DB9 serial straight-through cable, connect your
terminal or PC to the RS-232 port:
•
For the AT-8624T/2M and AT-8624PoE, the RS-232 port is on the front
panel.
•
For the AT-8648T/2SP, the RS-232 port is on the back panel.
2. Set the communication parameters on your terminal or terminal emulation
program to:
•
•
•
•
•
Bit rate: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
3. Log in.
After the switch has booted, the login prompt appears. If it does not
appear, press the Enter key several times.
When the switch starts for the first time, it automatically creates an
account with manager privileges. The account has the login name manager
and the password is friend.
At the login prompt, enter the login name and password:
Login: manager
Password: friend
The switch’s command prompt appears, and you can now use the CLI to
configure the switch.
4. Change the password.
A manager account left with the default password is a serious security risk.
Remember the new password as there is no way to retrieve it if it is lost.
To change the account password, use the set password command.
Installation & Safety Guide
5. Configure online help.
11
Before using online help, you must configure the help file by using the
command:
set help=<filename>.hlp
Help files have an HLP extension. To see a list of help files loaded on your
switch, use the command:
show files=*.hlp
6. Configure the switch.
Refer to the Software Reference for more information about configuring
the software. Alternatively, if you do not know the command syntax, use
any of the following to help you:
•
•
•
To display a list of help topics, use the help command.
To display help on a specific topic, use the help <topic> command.
To display a list of valid options, type a question mark or press the Tab
key at the end of a partial command.
•
To complete a parameter after you have typed enough letters to
uniquely match the desired one, press the Tab key.
7. Save the configuration.
Save your configuration to a new file by using the command:
create config=<filename>.cfg
Then set the switch to load this file when it restarts by using the command:
set config=<filename>.cfg
For information about configuring the software, see the AT-8600 Series Software
Reference.
Using the GUI to configure the AT-8624T/2M switch
This section describes how to establish a connection to the AT-8624T/2M switch
through the GUI so you can configure it before installing it in your LAN.
1. Select a PC to use and identify its subnet.
You can browse to the switch from any PC that is running a supported
operating system with a supported browser installed. JavaScript must be
enabled. If you are using a toolbar or plug-in on your browser to block pop-
ups, disable it while using the GUI. The GUI displays detailed configuration
options and information in pop-up windows.
12
AT-8600 Series Switch
2. Connect the PC to the switch.
Use an Ethernet cable to connect an Ethernet card on the PC to any one of
the switch ports.
You can browse to the router through any VLAN, as long as you give that
VLAN an IP address. These instructions assume you are using vlan1. All
switch ports belong to vlan1 by default.
3. Access the switch’s command line interface.
Access the CLI from the PC, as described in the previous section, “Using
the CLI to configure a switch” on page 10.
4. Enable IP.
enable ip
5. Assign the vlan1 interface an IP address in the same subnet as the PC.
add ip interface=vlan1 ip=ipaddress mask=mask
6. Save the configuration and set the switch to use it on bootup.
create config=your-name.cfg
set config=your-name.cfg
7. On the PC’s web browser, bypass the HTTP proxy server, if necessary.
8. Point your Web browser at IP address for vlan1.
9. At the login prompt, enter the user name and password.
User Name: manager <the default>
Password: friend
The System Status page is displayed. Select options from the sidebar menu
to configure and manage the switch.
For context-sensitive online help, click the Help button at the top of the
sidebar menu or on any pop-up page.
Installation & Safety Guide
13
Checking LEDs
The following tables outline how the switch and expansion modules report faults
and operational activities. Expansion modules are optional and can be purchased
separately.
System LEDs
LED
State
Off
Description
FAULT
Switch operation is normal.
Red
The switch or management software is
malfunctioning.
1 flash
A switch fan has failed.
3 flashes
The main PSU has failed and the RPS is now
providing power.
4 flashes
The RPS Monitor is set to ON, and the RPS
is not functioning, either because it has failed
or has been switched off.
5 flashes
7 flashes
The RPS Monitor is set to ON, but the RPS
is not connected.
For the AT-8624T/2M and AT-8624PoE
switches: An expansion module has been
inserted or removed while the switch is
powered on.
MASTER
RPS
Off
This LED is not supported.
Green
An optional redundant power supply is
connected to the switch.
Off
There is no optional redundant power
supply connected to the switch.
PWR
Green
Off
The switch is receiving power and the
voltage is within the acceptable range.
The switch is not receiving power.
Use the Mode Select button to toggle the Mode LEDs to the desired state.
Toggling the Mode Selection button does not affect the normal operations of the
switch.
14
AT-8600 Series Switch
Link and Mode LEDs for the AT-8624T/2M switch
LED
State
Description
LINK
Off
There is no link between the port and the
end-node.
Green
A valid link has been established between
the port and the end-node.
Mode - COL Off
No data collisions are occurring on the
port.
Flashing Green
Off
Green
Mode - FULL Off
Data collisions are occurring on the port.
The port is operating at 10 Mbps.
The port is operating at 100 Mbps.
Mode - 100
The port is operating in half-duplex
mode.
Green
The port is operating in full-duplex
mode.
Mode - ACT Off
Flashing Green
There is no activity on the port.
There is activity on the port. It is
transmitting and/or receiving data.
Installation & Safety Guide
15
Link and Mode LEDs for the AT-8624PoE switch
LED
State
Description
L/A Status
(Top LED)
Off
There is no link between the port
and the end-node.
Green
The port is operating at 100 Mbps.
Flashing Green
There is activity on the port. It is
transmitting and/or receiving data
at 100 Mbps.
Red
The port is operating at 10 Mbps.
Flashing Red
There is activity on the port. It is
transmitting and/or receiving data
at 10 Mbps.
Mode LEDs
Off
Either DC Mode or PoE Mode.
(Bottom LED)
D/C Mode
Off
There is no link between the port
and the end-node.
Green
Red
The port is operating in full duplex
mode.
The port is operating in half-duplex
mode.
Flashing Red
The port is operating in half-duplex
mode and data collisions are
occurring on the port.
PoE Mode
Off
There is no powered device
detected.
Green
The end-node is a powered device
and the port is providing power to
it.
Red
The port is experiencing a problem
providing PoE to the end-node.
Flashing Red
The port is connected to a
powered device but providing
power to it would exceed the
maximum PoE power budget of the
switch.
16
AT-8600 Series Switch
Link and Mode LEDs for the AT-8648T/2SP switch
LED
State
Description
LINK
Off
There is no link between the port
and the end-node.
Green
A valid link has been established
between the port and the end-
node.
Mode - COL
Off
No data collisions are occurring on
the port.
Flashing Green
Data collisions are occurring on
the port.
Mode - SPD
Mode - FDX
Off
The port is operating at 10 Mbps.
The port is operating at 100 Mbps.
Green
Off
The port is operating in half-duplex
mode.
Green
The port is operating in full-duplex
mode.
Mode - ACT
Off
There is no activity on the port
There is activity on the port.
Flashing Green
Installation & Safety Guide
17
SFP and 10/100/1000Base-T LEDs for the AT-8648T/2SP switch
LED
State
Description
LINK
Off
There is no link between the port
and the end-node.
Green
A valid link has been established
between the port and the end-
node.
Mode - COL
Mode - SPD
Mode - FDX
Mode - ACT
Off
No data collisions are occurring on
the port.
Flashing Green
Off
Data collisions are occurring on
the port.
The port is operating at 10/100
Mbps.
Green
Off
The port is operating at 1000
Mbps.
The port is operating in half-duplex
mode.
Green
The port is operating in full-duplex
mode.
Off
There is no activity on the port
There is activity on the port.
Flashing Green
18
AT-8600 Series Switch
Obtaining Documentation and Resources
The complete document set for the AT-8600 Series switches includes:
■
■
■
■
This Installation & Safety Guide, which also provides safety and statutory
information for the AT-8600 Series switch and its expansion options.
The AT-8600 Series Hardware Reference, which provides detailed information
on the switch unit and its hardware features.
The AT-8600 Series Software Reference, which provides detailed information
on configuring the switch unit and its software.
The AT-A65 Expansion Module Installation and Safety Guide which outlines the
procedure for installing the AT-A65 expansion module and provides
technical specifications for the module.
■
The AT-A45/xx Series, AT-A46, and AT-A47 Expansion Modules Installation Guide,
which outlines the procedure for installing these expansion modules, and
provides technical specifications for the modules.
You can download these documents and updates from
®
®
®
You need Adobe Acrobat Reader software to view, search, or print these
Other resources
How-To Notes describe a range of standard Allied Telesis solutions, and include
technical tips and guides to configuring specific hardware and software features.
You can download the latest How-To Notes from
MIBs supported by Allied Telesis products can be downloaded from
®
®
Microsoft Visio stencils for Allied Telesis products can be downloaded from
AT-TFTP Server for Windows is a TFTP (Trivial File Transfer Protocol) server for
transferring software versions, configuration scripts and other files between a
PC and the switch. You download AT-TFTP Server from
Contacting us
With locations covering all of the established markets in North America, Latin
America, Europe, Asia, and the Pacific, Allied Telesis provides localized sales and
technical support worldwide. To find the representative nearest you, visit us on
Installation & Safety Guide
19
Standards
Where applicable, the products in this document meet the following standards:
Category
Approval Agency and Requirement
UL60950-1
CAN/CSA-C22.2 No. 60950-1-03
EN60950-1
EN60825-1
Electromagnetic Compliance
FCC CFR47 Part 15 Class A
EN55022 Class A
EN61000-3-2
EN61000-3-3
VCCI Class A
AS/NZS CISPR22 Class A
Immunity
EN55024
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
20
AT-8600 Series Switch
Safety
WARNING: In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
WARNING: Class 1 Laser product.
WARNING: Do not stare into the laser beam.
CAUTION: Use of controls or adjustments of performance or procedures
other than those specified herein may result in hazardous radiation exposure.
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock, do not remove the cover. No user-serviceable
parts inside. This unit contains HAZARDOUS VOLTAGES and should only be
opened by a trained and qualified technician.
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of
LIGHTNING ACTIVITY.
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO
DE-ENERGIZE EQUIPMENT, disconnect the power cord.
ELECTRICAL - TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a
properly wired earth ground socket outlet. An improperly wired socket outlet
could place hazardous voltages on accessible metal parts.
PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the
equipment and shall be easily accessible.
CAUTION: Air vents must not be blocked and must have free access to the
room ambient air for cooling.
OPERATING TEMPERATURE: This product is designed for a maximum ambient
temperature of 40 degrees C.
ELECTRICAL - AC MAINS CIRCUIT OVERLOADING
When installing product, consideration must be given to the accumulative
nameplate ratings when connecting the equipment to the AC supply wiring.
CAUTION: MECHANICAL LOADING - Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due to uneven loading.
Installation & Safety Guide
Lithium Battery - Should only be changed by authorised service personnel.
21
CAUTION: Danger of explosion if battery incorrectly replaced. Replace only
with Lithium Battery, type CR2032, and dispose of in accordance with the
manufacturer’s recommendations and all local codes.
ALL COUNTRIES: Install product in accordance with local and National
Electrical Codes.
WARNING: Only trained and qualified personnel are allowed to install or
replace this equipment.
CAUTION: This unit does not contain serviceable components. Please return
damaged units for servicing.
CAUTION: The AT-8624PoE Ethernet ports are only intended for installation in
Environment A as defined in IEEE 802.3af. All interconnected equipment must be
contained in the same building including the interconnected equipment’s
associated LAN connections.
CAUTION: The surface-mount fuses F1 to F24 on the Power over Ethernet
daughterboard in the AT-8624PoE switch are 60V, max 2A fuses. These fuses are
not field-replaceable, and should only be serviced by a trained Allied Telesis
service technician.
Sicherheit
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen
hervorrufen. In diesem Fall müßte der Anwender angemessene
Gegenmaßnahmen ergreifen.
WARNUNG Laserprodukt der Klasse 1.
WARNUNG Nicht direkt in den Strahl blicken.
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren
Teile. Das Gerät steht unter Hochspannung und darf nur von qualifiziertem
technischem Personal geöffnet werden.
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines
Gewitters ausführen.
22
AT-8600 Series Switch
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER
STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER
STECKDOSE ZIEHEN.
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein
unvorschriftsmäßiger Anschluß kann die Metallteile des Gehauses unter
gefährliche elektrische Spannungen setzen.
STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung
angebracht werden und leicht zugänglich sein.”
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen
freien Zugang zur Raumluft haben.
BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer
Umgebungstemperatur von nicht mehr als 40° C entworfen.
NETZSICHERUNG
Bei der Installation muß der auf dem Typenschild angezeigte Nennwert des
Gerätes für den Anschluß an das Netz beachtet werden.
VORSICHT: RAHMENEINBAU
Die Geräte müssen so in den Rahmen montiert werden, daß keine Gefahren
durch unebenen inbau des Rahmens verursacht werden.
Lithium-Batterie - Sollte nur von einem geschulten qualifizierten Techniker
ausgetauscht werden.
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Nur
mit einer gleichen Batterie oder einem gleichwertigen Batterietyp nach
Empfehlung des Herstellers ersetzen. Gebrauchte Batterien nach Anweisungen
des Herstellers beseitigen.
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen
Vorschriften entsprechen.
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste
Schalldruckpegel beträgt 70dB(A) oder weniger gemäss EN ISO 7779
Installation & Safety Guide
23
Sikkerhed
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.
Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.
ADVARSEL Laserprodukt av klasse 1.
ADVARSEL Stirr ikke på strålen.
ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre
dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE
STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen
ud af stikket.
ELEKTRISK - KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet
med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret
stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele.
UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og
skal være lettilgængelig.
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en omgivende
temperatur på maksimum 40 grader C.
ELEKTRISK-OVERBELASTNING AF SPÆNDINGSKREDSLØBET
Ved installation af produktet, bør der tages hensyn til den kumulative kapacitet
der angives på navneskiltet, når udstyret forbindes med vekselstrømsledningen.
ADVARSEL: MEKANISK OPSTILLING-Udstyret skal opstilles i stativet, på en
sådan måde, at der kke opstår fare p.g.a. ujævn opstilling.
24
AT-8600 Series Switch
Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker.
ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun med
samme eller en tilsvarende type der anbefales af producenten. Kassér brugte
batterier i overensstemmelse med producentens instruktioner.
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal
og national lovgivning for elektriske installationer.
Veiligheid
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in
welk geval de gebruiker verplicht kan worden om gepaste maatregelen te
nemen.
WAARSHUWING Klasse-1 laser produkt.
WAARCHUWING Neit in de straal staren.
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen.
Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden
kunnen worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag
alleen worden geopend door een daartoe opgeleide en bevoegde technicus.
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE
STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE
MAKEN: de stroomkabel ontkoppelen.
ELEKTRISCHE TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn
op een juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de
metalen onderdelen waarmee de gebruiker eventueel in aanraking komt onder
gevaarlijke spanning stellen.
AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de
apparatuur geïnstalleerd en is gemakkelijk te bereiken.”
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de
omgevingslucht ongehinderd toelaten voor afkoeling.
Installation & Safety Guide
25
BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag niet
meer bedragen dan 40 graden Celsius.
ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT
Tijdens de installatie van het produkt dient men rekening te houden met de
gecombineerde waarden op de naamplaatjes bij het aansluiten van het toestel op
de wisselstroom-voedingsdraden.
LOPGELET: MECHANISCH LADEN - De montage van het toestel in het rek
dient zo uitgevoerd te worden dat geen gevaar ontstaat door een ongelijke
lading.
Lithium batterij. Mag alleen worden vervangen door een daartoe opgeleide en
bevoegde technicus.
OPGELET: Gevaar voor ontploffing indien de batterij verkeerd wordt vergangen.
Alleen vervangen door hetzelfde of een gelijkwaardig, door de fabrikant
aanbevolen type.
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.
Sécurité
MISE EN GARDE : dans un environnement domestique, ce produit peut
provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra
prendre les mesures adéquates.
ATTENTION Producit laser di classe 1.
ATTENTION Ne pas fixer le faisceau des yeux.
INFORMATION SUR LES RISQUES ÉLECTRIQUES
AVERTISSEMENT: DANGER D’ÉLECTROCUTION
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un
technicien dûment qualifié.
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS
CIRCUIT. POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le
cordon.
26
AT-8600 Series Switch
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être
branchée dans une prise femelle correctement mise à la terre car des tensions
dangereuses risqueraient d’atteindre les pièces métalliques accessibles à
l’utilisateur.
EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit
être placée près de l’équipement et facilement accessible”.
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air
ambiant de circuler librement pour le refroidissement.
TEMPÉRATURE DE FONCTIONNEMENT: Ce matériel est capable de tolérer
une température ambiante maximum de ou 40 degrés Celsius.
SURCHARGE DES CIRCUITS PRINCIPAUX DE COURANT ALTERNATIF
ÉLECTRIQUE
Lors de l'installation du matériel, il faut prendre en compte la somme des
puissances indiquées sur les étiquettes au moment de connecter le matériel à
une source de courant alternatif.
ATTENTION : RÉPARTITION DE LA CHARGE MÉCANIQUE - Le montage du
matériel dans le bâti doit être effectué de telle manière que la répartition de la
charge mécanique ne pose aucun danger.
Pile en Lithium-Doit uniquement être remplacée par un technicien dûment
qualifié
ATTENTION : Un danger d'explosion existe en cas de remplacement incorrect
de la pile. Remplacer uniquement avec une pile du même type ou d'un type
recommandé par le fabricant. Mettre au rebut lespiles usagées conformément
aux instructions du fabricant).
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques
nationales et locales.
Turvallisuus
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä,
missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.
VAROITUS Luokan 1 Lasertuote.
VAROITUS Älä katso säteeseen.
Installation & Safety Guide
27
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
VAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain
koulutettu ja pätevä teknikko.
SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN
VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto.
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa
metalliosat vaarallisille jännitteille.
PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle
ja siihen on oltava esteetön pääsy.”
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys
ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.
KÄYTTÖLÄMPÖTILA: Tämä tuote on suunniteltu ympäröivän ilman
maksimilämpötilalle 40°C.
SÄHKÖ-VAIHTORVIRTASÄHKÖPIIRIN YLIKUORMITUS
Tuotetta asennettaessa on otettava huomioon osien nimikilvissä osoitettu teho
silloin kun osat liitetetään vaihtovirtaverkkoon.
HUOMAUTUS: MEKAANINEN KUORMITUS--Osien asennuksen alustaan
tulee tapahtua siten, että epätasainen kuormitus ei aiheuta vaaraa.
Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko.
Varoitus: Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai
vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot
valmistajan ohjeiden mukaan.
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten
sähköturvallisuusmääräysten mukaisesti.
28
AT-8600 Series Switch
Norme di Sicurezza
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio
interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli
adeguati provvedimenti.
AVVERTENZA Prodotto laser di Classe 1.
AVERTENZA Non fissare il raggio con gli occhi.
AVVERTENZE ELETTRICHE
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti
interne non sono riparabili dall’utente. Questa unità ha TENSIONI
PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato.
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante
PRECIPITAZIONI TEMPORALESCHE.
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME
DISPOSITIVO DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL
DISPOSITIVO staccare il cavo di alimentazione.
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve
essere inserita in una presa di corrente specificamente dotata di messa a terra.
Una presa non cablata in maniera corretta rischia di scaricare una tensione
pericolosa su parti metalliche accessibili.
APPARECCHIATURA COLLEGABILE, la presa va installata vicino
all’apparecchio per risultare facilmente accessibile”.
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero
ricircolo dell’aria ambiente per il raffreddamento.
TEMPERATURA DI FUNZIONAMENTO: Questo prodotto è concepito per una
temperatura ambientale massima di 40 gradi centigradi.
ELETTRICITÀ - SOVRACCARICO DEL CIRCUITO DI RETE A C.A.
Durante l'installazione ed il collegamento del dispositivo alla rete di
alimentazione a corrente alternata, è necessario tenere in considerazione le
capacità cumulative riportate sulla targhetta.
Installation & Safety Guide
29
ATTENZIONE: CARICAMENTO MECCANICO - Il montaggio del dispositivo
sul supporto va effettuato in maniera tale da evitare qualsiasi potenziale
condizione di pericolo eventualmente dovuta al montaggio irregolare.
Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato.
ATTENZIONE: l'errata sostituzione della batteria può causare pericolo di
esplosioni. Sostituire solamente con lo stesso tipo o con uno equivalente
raccomandato dal produttore. Eliminare le batterie usate secondo le istruzioni
del produttore.
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative
elettriche nazionali.
Sikkerhet
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet
forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige
forholdsregler.
ADVARSEL Laserprodukt av klasse 1.
ADVARSAL Stirr ikke på strålen.
ELEKTRISITET
ADVARSEL: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.
FARE FOR LYNNEDSLAG
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR
Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.
ELEKTRISK - TYPE 1- KLASSE UTSTYR
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt
jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig
spenninger i lett t ilgjengelige metalldeler.
UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av
utstyret og skal være lett tilgjengelig.”
30
AT-8600 Series Switch
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med
romtemperatur for avkjøling.
DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum
romtemperatur på 40 grader celsius.
ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØP
Når produktet installeres, må de samlede navneplateverdiene kontrolleres nøye
når strøm påsettes.
FORSIKTIG: MEKANISK LASTNING Installering av utstyret på hyllen må
utføres på en slik måte at ingen farlige situasjoner oppstår som en følge av ujevn
lastning.
Litiumbatteri — Må kun byttes ut av en faglig kvalifisert tekniker.
FORSIKTIG: Eksplosjonsfare hvis batteriet feilinnsettes.Batteriet må bare
erstattes med samme type eller en tilsvarende type som er anbefalt av
fabrikanten. Batteriene må kasseres i samsvar med fabrikantens instruksjoner.
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
Segurança
AVISO: Num ambiente doméstico este produto pode causar interferência na
radiorrecepção e, neste caso, pode ser necessário que o utente tome as
medidas adequadas.
AVISO Produto laser de classe 1
AVISO Não olhe fixamente para o raio.
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que
possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS
PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM
DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O
EQUIPAMENTO, desconecte o cabo de ALIMENTAÇÃO.
Installation & Safety Guide
31
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O
plugue de alimentação deve ser conectado a uma tomada com adequada ligação
de fio terra. Tomadas sem adequada ligação de fio terra podem transmitir
voltagens perigosas a peças metálicas expostas.
EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto
do equipamento e ser de fácil acesso.”
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter
acesso livre ao ar ambiente para arrefecimento adequado do aparelho.
TEMPERATURA DE FUNCIONAMENTO: Este produto foi projetado para uma
temperatura ambiente máxima de 40 graus centígrados.
ELÉTRICO - SOBRECARGA DA REDE DE CORRENTE ALTERNADA (AC)
Antes de instalar o produto, verifique o efeito cumulativo da conexão de
diversos aparelhos àrede de corrente alternada através das etiquetas que
indicam potência ou amperagem.
CUIDADO: CARREGAMENTO - O equipamento deverá ser montado no
suporte de montagem de forma tal que não cause perigo devido a carregamento
não uniforme.
Bateria de lítio - Só deve ser trocada por técnico qualificado e treinado.
CUIDADO: Se a bateria não for devidamente instalada há perigo de explosão.
Substitua somente pelo mesmo tipo ou equivalente, conforme recomendado
pelo fabricante. Descarte baterias usadas, de acordo com as instruções
fornecidas pelo fabricante.
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e
locais para instalações elétricas.
32
AT-8600 Series Switch
Seguridad
ADVERTENCIA: en un entorno doméstico, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las
medidas que sean convenientes al respecto.
¡ADVERTENCIA! Producto láser Clase 1.
¡ADVERTENCIA! No mirat fijamente el haz.
AVISOS ELECTRICOS
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún
componente en el interior al cual puede prestar servicio el usuario. Esta unidad
contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y
calificado.
PELIGRO DE RAYOS
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los
equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN
DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO,
desconecte el cable de alimentación.
ELECTRICO - EQUIPO DEL TIPO CLASE 1
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que
conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está
correctamente instalado podría ocasionar tensiones peligrosas en las partes
metálicas que están expuestas.
EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en
un lugar con acceso fácil”.
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán
tener acceso libre al aire ambiental de la sala para su enfriamiento.
TEMPERATURA REQUERIDA PARA LA OPERACIÓN: Este producto está
diseñado para una temperatura ambiental máxima de 40 grados C.
ELECTRICO - SOBRECARGA DEL CIRCUITO PRIMARIO DE CORRIENTE
ALTERNA
Al instalarse el producto deberán considerarse las potencias nominales
acumulativas, cuando se conecta el equipo al cable de alimentación de corriente
alterna.
Installation & Safety Guide
33
ATENCION: CARGA MECANICA - El montaje del equipo en el bastidor debe
realizarse de manera tal que no cause una condición peligrosa debido a la
distribución desigual del peso.
Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado.
ATENCION: Peligro de explosión si la batería no se reemplaza en forma
correcta. Reemplace sólo con el mismo tipo o equivalente que recomienda el
fabricante. Deseche las baterías usadas según las instrucciones del fabricante.
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos
Eléctricos locales y nacionales.
Säkerhet
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket
kan tvinga användaren till att vidtaga erforderliga åtgärder.
VARNING! Laserprodukt av klass 1.
VARNING! Laserstrålning när enheten är öppen.
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket.
Det finns inga delar inuti som behöver underhållas. Denna apparat är under
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.
FARA FÖR BLIXTNEDSLAG
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT
KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln.
ELEKTRISKT - TYP KLASS 1 UTRUSTNING
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara
ansluten till ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande
metalldelar utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när
den ansluts till ett nätverk.
UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och
vara lättåtkomligt”.
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande
rumsluft för avsvalning.
34
AT-8600 Series Switch
DRIFTSTEMPERATUR: Denna produkt är konstruerad för rumstemperatur ej
överstigande 40 grader Celsius.
ELEKTRISKT - ÖVERBELASTNING AV VÄXELSTRÖMSNÄTET: När
produkten installeras bör den sammanlagda effekten på namnplåten beaktas när
apparaten ansluts till växelströmsnätet.
VARNING: MEKANISK BELASTNING: Utrustningen ska installeras i chassit på
så sätt att fara inte uppstår p g a ojämn belastning.
Litium batteri - Får endast bytas av utbildade och kvalificerade tekniker.
VARNING: Risk för explosion om felaktigt batteri används. Byt endast mot
samma eller likvärdig typ batteri, rekommenderat av tillverkaren. Kassera
använda batterier i enlighet med tillverkarens instruktioner.
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga
bestämmelser för elektrisk utrustning.
|