|
Acer LCD M onitor
User Guide
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.
Special notes on LCD monitors
The following are normal with the LCD monitor and do not indicate a problem.
•
Due to the nature of the fluorescent light, the screen may flicker during initial
use. Turn off the power switch and then turn it on again to make sure the flicker
disappears.
•
•
•
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
The LCD screen has 99.99% or more effective pixels. It may include blemishes of
0.01% or less such as a missing pixel or pixel lit all the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In this
case, the screen is recovered slowly by changing the image or turning off the power
switch for a few hours.
Cleaning your monitor
Please carefully follow these guidelines when cleaning the monitor:
•
•
Always unplug the monitor before cleaning.
Use a soft cloth to wipe the screen and cabinet front and sides.
iii
Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and
located as close to the equipment operator as possible. W hen you need to disconnect
power from the equipment, be sure to unplug the power cord from the electrical outlet.
Safe listening
To protect your hearing, follow these instructions.
•
Gradually increase the volume until you can hear it clearly and comfortably and
without distortion.
•
•
•
•
After setting the volume level, do not increase it after your ears have adjusted.
Limit the amount of time listening to music at high volume.
Avoid turning up the volume to block out noisy surroundings.
Turn the volume down if you can’t hear people speaking near you.
Warnings
•
Do not use this product near water.
•
Do not place this product on an unstable cart, stand or table. If the product falls, it
could be seriously damaged.
•
•
Slots and openings are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug or other similar surface. This product should never be placed near or over
a radiator or heat register, or in a built-in installation unless proper ventilation is
provided.
Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto or into the product.
•
•
To avoid damage of internal components and to prevent battery leakage, do not
place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment which will
probably cause unexpected short current or damage internal devices.
•
•
The adapter is only used for this monitor, do not be used for other purposes.
Your device uses one of the following power supplies:
M anufacture : Hipro Electronics Co.,Ltd. M odel:HP-A0301R3 (S220HQL M odel)
M anufacture : Delta Electronics Inc., M odel: ADP-30M H B (S220HQL M odel)
M anufacture : Delta Electronics Inc., M odel: ADP-40PH BB (S230HL M odel)
Using electrical power
•
This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or local
power company.
iv
•
•
Do not allow anything to rest on the power cord. Do not locate this product where
people will walk on the cord.
If an extension cord is used with this product, make sure that the total ampere rating
of the equipment plugged into the extension cord does not exceed the extension
cord ampere rating. Also, make sure that the total rating of all products plugged into
the wall outlet does not exceed the fuse rating.
•
•
Do not overload a power outlet, strip or receptacle by plugging in too many devices.
The overall system load must not exceed 80% of the branch circuit rating. If power
strips are used, the load should not exceed 80% of the power strip’s input rating.
This product’s power cord is equipped with a three-wire grounded plug. The plug
only fits in a grounded power outlet. M ake sure the power outlet is properly
grounded before inserting the power cord plug. Do not insert the plug into a non-
grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric
shock and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to
replace the power cord set, make sure that the new power cord meets the following
requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V
minimum, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to qualified
service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need for service
the product does not operate normally after following the operating instructions
v
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
Potentially explosive environments
Switch off your device in any area with a potentially explosive atmosphere and obey all
signs and instructions. Potentially explosive atmospheres include areas where you would
normally be advised to turn off your vehicle engine. Sparks in such areas could cause
an explosion or fire resulting in bodily injury or even death. Switch off the device near
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel
depots, storage and distribution areas; chemical plants; or where blasting operations are
in progress. Areas with a potentially explosive atmosphere are often, but not always,
marked. They include below deck on boats, chemical transfer or storage facilities,
vehicles using liquefied petroleum gas (such as propane or butane), and areas where the
air contains chemicals or particles such as grain, dust or metal powders.
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the reach
of small children.
IT Equipment Recycling Information
Acer is strongly committed to environmental protection and views recycling, in the form
of salvaging and disposal of used equipment, as one of the company’s top priorities in
minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental effects of our business and strive to
identify and provide the best working procedures to reduce the environmental impact
of our products.
For more information and help when recycling, please go to this website:
other products.
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global
environment, please recycle. For more information on the Waste
from Electrical and Electronics Equipment (W EEE) regulations, visit
vi
LCD pixel statement
The LCD unit is produced with high-precision manufacturing techniques. Nevertheless,
some pixels may occasionally misfire or appear as black or red dots. This has no effect on
the recorded image and does not constitute a malfunction.
This product has been shipped enabled for power management:
•
•
•
Activate display’s Sleep mode within 15 minutes of user inactivity.
Activate computer’s Sleep mode within 30 minutes of user inactivity.
Wake the computer from Sleep mode by pushing the power button.
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use. Users are
also at risk of physical injury after long hours of working in front of a computer. Long
work periods, bad posture, poor work habits, stress, inadequate working conditions,
personal health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis
or other musculoskeletal disorders. The following symptoms may appear in the hands,
wrists, arms, shoulders, neck or back:
•
•
•
•
•
numbness, or a burning or tingling sensation
aching, soreness or tenderness
pain, swelling or throbbing
stiffness or tightness
coldness or weakness
If you have these symptoms, or any other recurring or persistent discomfort and/or pain
related to computer use, consult a physician immediately and inform your company’s
health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest,
or raising your sitting height to achieve maximum comfort. Observe the following tips:
•
•
•
refrain from staying too long in one fixed posture
avoid slouching forward and/or leaning backward
stand up and walk around regularly to remove the strain on your leg muscles
vii
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room
lighting, poorly focused screens, very small typefaces and low-contrast displays could
stress your eyes. The following sections provide suggestions on how to reduce eyestrain.
Eyes
•
•
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the monitor and focusing on a
distant point.
•
Blink frequently to keep your eyes from drying out.
Display
•
•
Keep your display clean.
Keep your head at a higher level than the top edge of the display so your eyes point
downward when looking at the middle of the display.
•
•
Adjust the display brightness and/or contrast to a comfortable level for enhanced
text readability and graphics clarity.
Eliminate glare and reflections by:
•
placing your display in such a way that the side faces the window or any light
source
•
•
•
•
•
minimizing room light by using drapes, shades or blinds
using a task light
changing the display’s viewing angle
using a glare-reduction filter
using a display visor, such as a piece of cardboard extended from the display’s top
front edge
•
•
Avoid adjusting your display to an awkward viewing angle.
Avoid looking at bright light sources, such as open windows, for extended periods of
time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and
productive:
•
•
•
•
Take short breaks regularly and often.
Perform some stretching exercises.
Breathe fresh air as often as possible.
Exercise regularly and maintain a healthy body.
viii
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih
Taipei Hsien 221, Taiwan
Tel : 886-2-2696-1234
Fax : 886-2-2696-3535
Declaration of Conformity
Acer Incorporated
We,
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, E-mail: [email protected]
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
Hereby declare that:
Product:
LCD Monitor
Trade Name:
Model Number:
SKU Number:
Acer
S220HQL; S230HL
S220HQL xxxxxx ; S230HL xxxxxx
(“x” = 0~9, a ~ z, A ~ Z, or blank)
Is compliant with the essential requirements and other relevant provisions of the following EC directives,
and that all the necessary steps have been taken and are in force to assure that production units of the
same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following harmonized
standards:
-. EN55022, AS/NZS CISPR22 Class B.
-. EN55024
-. EN61000-3-2, Class D
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
-. EN60950-1
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances
in Electrical and Electronic Equipment:
-. The maximum concentration values of the restricted substances by weight in homogenous material are:
Lead
0.1% Polybrominated Biphenyls (PBB’s)
0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%
0.01%
0.1%
Mercury
Hexavalent Chromium 0.1% Cadmium
Directive 2009/125/EC with regard to establishing a framework for the setting of
ecodesign requirements for energy-related product.
Year to begin affixing CE marking 2011.
Jan. 28, 2011
Easy Lai /Manager
Date
Regulation, Acer Inc.
ix
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
LCD Monitor
Model Number:
SKU Number:
S220HQL ; S230HL
S220HQL xxxxxx ; S230HL xxxxxx
(“x” = 0~9, a ~ z, A ~ Z or Blank)
Name of Responsible Party:
Address of Responsible Party:
Acer America Corporation
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
x
Unpacking
Please check that the following items are present when you unpack the box, and save
the packing materials in case you need to ship or transport the monitor in the future.
LCD monitor
User guide
Quick start guide
HDM I cable
(Optional)
D-sub cable
AC Power cord
DVI cable
(Optional)
AC Adapter
1
Attaching the base (for selected models)
Note: Remove the monitor and monitor base from its packaging.
Carefully place the monitor face-down on a stable surface -- use a
cloth to avoid scratching the screen.
1
2
Attach the monitor stand arm to the base.
Ensure that the base is locked onto the monitor stand arm.
•
Secure the base to the monitor stand arm by turning the white screw using the
integrated tab or a suitable coin. (for selected models)
Note: Take care when performing the installation to avoid injuring
yourself.
2
5
Screen position adjustment
To optimize the viewing position, you can adjust the
monitor tilt, using both of your hands to hold the edges
of the monitor. The monitor can be adjusted to 15
degrees up or 5 degrees down.
Connecting the adapter and AC Power cord
•
Check first to make sure that the power cord you use is the correct type required for
your area.
•
The monitor has a universal power supply that allows operation in either 100/120 V
AC or 220/240 V AC voltage area. No user-adjustment is required.
•
•
Plug one end of the AC power cord to the Adapter, and plug the other end into an
AC outlet.
For units using 120 V AC:
Use a UL-listed cord set, type SVT wire and plug rated 10 A/125 V.
•
For units using 220/240 V AC:
Use a cord set consisting of H05VV-F cord and plug rated 10 A/250 V. The cord set
should have the appropriate safety approvals for the country in which the equipment
will be installed.
Power saving
The monitor will be switched to “power saving” mode by the control signal from the
display controller, as indicated by the blinking blue light.
Mode
On
LED light
Blue
Standby/Power saving
Blinking Blue
The power saving mode will be kept until a
control signal has been detected or the keyboard
or mouse is activated. The recovery time from
“power saving” mode back to “on” is around 3
seconds.
LED indicator
3
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, the
monitor is able to plug-and-play. The DDC is a communication protocol through which
the monitor automatically informs the host system about its capabilities; for example,
supported resolutions and corresponding timing. The monitor supports the DDC2B
standard.
Connector pin assignment
1
5
10
15
6
11
15-pin color display signal cable
PIN No. Description
PIN No. Description
1
2
3
4
5
6
7
8
Red
9
+5 V
Green
10
11
12
13
14
15
Logic ground
Blue
M onitor ground
DDC-serial data
H-sync
M onitor ground
DDC-return
R-ground
G-ground
B-ground
V-sync
DDC-serial clock
4
24-pin color display signal cable
PIN No. Description
PIN No. Description
1
2
TM DS data 2-
TM DS data 2+
TM DS data 2/4 shield
NC
13
14
15
16
17
18
19
20
21
22
23
24
NC
+5 V power
3
GND (return for +5 V hsync.vsync)
Hot-plug detection
TM DS data 0-
TM DS data 0+
TM DS data 0/5 shield
NC
4
5
NC
6
DDC clock
DDC data
7
8
NC
9
TM DS data 1-
TM DS data 1+
TM DS data 1/3 shield
NC
NC
10
11
12
TM DS clock shield
TM DS clock+
DDC TM DS clock-
19-pin color display signal cable
19 1715 13 11 9 7 5 3 1
18 1614 12 10 8 6 4 2
PIN No. Description
PIN No. Description
1
3
TM DS Data2+
TM DS Data2-
TM DS Data1 Shield
TM DS Data0+
TM DS Data0-
TM DS Clock Shield
CEC
2
4
TM DS Data2 Shield
TM DS Data1+
TM DS Data1-
5
6
7
8
TM DS Data0 Shield
TM DS Clock+
9
10
12
14
16
18
11
13
15
17
19
TM DS Clock-
Reserved (N.C. on device)
SDA
SCL
DDC/CEC Ground
Hot Plug Detect
+5V Power
5
Standard timing table
No.
Mode
Resolution
Refresh Rate
1
640x480
60
72
66.7
70
56
60
72
60
60
70
75
60
60
60
60
60
60
60
60
60
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
VGA
2
640x480
3
M AC
VESA
640x480
4
720x400
5
800x600
6
800x600
SVGA
7
800x600
8
1024x600
1024x768
1024x768
1152x864
1280x960
1280x1024
1280x720
1280x800
1360x768
1440x900
1680x1050
1600x1200
1920x1080
9
XGA
10
11
12
13
14
15
16
17
18
19
20
VESA
SXGA
VESA
W XGA
W XGA+
W SXGA+
UXGA
VESA
6
Installation
To install the monitor on your host system, please follow the steps below:
Steps
1
Connect the video cable
a
M ake sure both the monitor and computer are switched off.
Connect the VGA video cable to the computer.
Connect the digital cable
b
c
(1) M ake sure both the monitor and computer are switched off.
(2) DVI Cable (Optional, only Dual-Input M odel)
a. M ake sure both the monitor and computer are powered-OFF.
b. Connect the DVI cable to the computer.
(3) HDM I Cable (Optional, only HDM I-Input M odel)
a. M ake sure both the monitor and computer are powered-OFF.
b. Connect the HDM I cable to the computer.
2
Connect the adapter
a
Connect the AC cord to the adapter.
b
Connect one end of the adapter to the monitor and the other end to a properly
grounded, AC outlet.
3
4
Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very important.
If the monitor does not function properly, please refer to the troubleshooting
section to diagnose the problem.
DVI
D-SUB
DC-IN
HDMI
2
DC
HDMI
DVI
D-SUB
DVI
D-SUB
DC-IN
HDMI
7
Users controls
5 4 3
2
1
Panel controls
No. Item
Description
1
Power button/
Turn the monitor on/off.
indicator
Blue indicates power on. Blinking blue indicates standby/
power saving mode.
2
< / > button
Press the < / > button to navigate to the desired function,
and press the Menu button to select the function. Press the
< / > button to change the settings of the current function.
3
4
M enu/Enter
button
Press to view the OSD menu. Press it again to enter a
selection in the OSD menu.
Auto/Exit button
•
•
W hen the OSD menu is active, press this button to exit
the OSD menu.
W hen the OSD menu is inactive, press this button for
two seconds to activate the Auto Adjustment function
and the monitor will automatically optimize the display
position, focus, and clock of your display.
5
Empowering Key Press this button to open the Acer eColor M anagement OSD
and access the scenario modes.
8
Using the Shortcut Menu
AUTO
Input
Press any of the function buttons (Empowering Key, Auto button, or Menu button) to
open the shortcut menu. The shortcut menu lets you quickly select the most commonly
accessed settings.
Icon
Item
Description
Empowering
Press the Empowering Key to open the Acer eColor
M anagement and access the scenario modes.
Auto
Press the Auto button to activate the Auto Adjustment
function and the monitor will automatically optimize the
display position, focus, and clock of your display.
AUTO
M enu
Volume
Input
Press the Menu button to activate the OSD menu.
Press the Volume button to adjust volume. (Optional, only
Audio-Input M odel)
Press the Input button to select from different video
sources that may be connected to your monitor. (Optional,
only Dual-Input M odel or HDM I-Input M odel)
Input
Acer eColor Management
Operation instructions
1
Press the Empowering Key to open the Acer eColor M anagement OSD menu and
access the scenario modes.
mpowering Technology
User
ECO Standard Graphics Movie
Adjust/Exit
2
3
Press the < / > button to select the desired mode.
Press the Auto button to confirm the selection and exit Acer eColor M anagement.
9
Features and benefits
Icon
Mode type
Description
User mode
User-defined. Settings can be fine-tuned to suit any
situation.
ECO mode
Adjusts the settings to reduce power consumption.
Standard mode
Graphic mode
M ovie mode
Default settings. Reflects native display capability.
Enhances colors and emphasizes fine detail. Pictures and
photographs appear in vibrant colors with sharp detail.
Displays scenes in clearest detail. Presents great visuals,
even in unsuitably-lit environments.
Using the OSD Menus
Note: The following content is for general reference only. Actual
product specifications may vary.
Your LCD monitor is equipped with an on-screen display (OSD) menu for making various
adjustments and settings.
Press the Menu button to open the OSD menu. You can use the OSD menu to adjust the
picture quality, OSD timeout, and general settings.
10
Picture M enu
The Picture menu is used for adjusting the picture quality.
Picture
Acer eColor Management
Brightness
Contrast
77
56
50
50
30
50
H.Position
V.Position
Focus
Clock
Colour Temp
Auto Config
Warm
Exit
1
2
Press the Menu button to bring up the OSD menu.
Press the < / > button to select
Picture menu.
Picture and press the Menu button to enter the
The following options are available in the Picture menu: Acer ecolor M anagement,
Brightness, Contrast, H. Position, V. Position, Focus, Clock, Colour Temp, and Auto
Config.
3
4
Press the < / > button to scroll through the Picture options, and press the Menu
button to enter its sub-menu.
Press the < / > button to adjust/select the setting and press the Auto button to
confirm.
11
OSD M enu
The OSD menu is used for adjusting the OSD timeout setting.
OSD
OSD Timeout
10
Exit
1
2
Press the Menu button to bring up the OSD menu.
Press the < / > button to select
OSD menu.
OSD and press the Menu button to enter the
3
To adjust the OSD Timeout setting, press the Menu button to enter its sub-menu.
4
Press the < / > button to select the desired time interval and press the Auto button
to confirm.
Setting M enu
The Setting menu is used for adjusting the general settings for current input signal such
as aspect ratio, OSD language, and etc.
Setting
Wide Mode
DDC/CI
ACM
Full
ON
OFF
Input
VGA
Language
Reset
English
Exit
12
1
2
Press the Menu button to bring up the OSD menu.
Press the < / > button to select
Setting and press the Menu button to enter the
Setting menu.
The following options are available in the Setting menu: W ide M ode, DDC/CI, ACM ,
Input, Language, and Reset.
3
4
Press the < / > button to scroll through the Setting options, and press the Menu
button to enter its sub-menu.
Press the < / > button to adjust/select the setting and press the Auto button to
confirm.
Information M enu
The Information menu displays the basic information of the LCD monitor.
Information
1920x1080
H:68KHz V:60Hz
VGA Input
S/N:ETRLA00803104000502400
Exit
1
2
Press the Menu button to bring up the OSD menu.
To view the basic information of the LCD monitor, press the < / > button to select
Information.
13
Troubleshooting
Before sending your LCD monitor for servicing, please check the troubleshooting list
below to see if you can self-diagnose the problem.
VGA Mode
Problem
LED status
Blue
Remedy
No picture visible
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
settings.
Off
Check the power switch.
Check if the power cord is properly connected
to the monitor.
Blinking Blue
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
Unstable picture
Blue
Blue
Check if the specification of graphics adapter
and monitor is in compliance which may be
causing the input signal frequency mismatch.
Abnormal picture
(Image is missing,
off-center, too large
or too small on the
screen.)
Using the OSD menu, adjust focus, clock,
H-position and V-position with non-standard
signals.
Check the display setting on your system. In
case of a missing image, please select another
resolution or vertical refresh rate.
Wait for a few seconds after adjusting
the size of the image before changing or
disconnecting the signal cable or switching
off the monitor.
14
DVI/HDMI mode (Optional)
Problem
LED status
Remedy
No picture visible
Blue
Using the OSD menu, adjust brightness and
contrast to maximum or reset to their default
settings.
Off
Check the power switch.
Check if the AC power cord is properly
connected to the monitor.
Blinking Blue
Check if the video signal cable is properly
connected at the back of monitor.
Check if the computer system is switched on
and in power saving/standby mode.
15
|