Operation Instructions
X-Fade-6
Control Station Operation with Infrared Remote Control
1.Product Descriptions
X-FADE-6
0
0
5
5
10
10
We wish to express our gratitude for your purchasing our digital product X-Fade-6.
You now hold a premiere, hybrid 6-ch DMX controller combining with 6 channel
faders. Its compact and portable design is convenient to mount and easy to
operate for users. Its key features consists of as the following:
CH. 1
CH. 2
CH. 3
CH. 4
CH. 5
CH. 6
0
0
0
0
5
5
5
5
10
10
10
10
USITT DMX-512(1990) Multiplexed Digital Control
Up to 6 DMX channels and 6 channel control faders
6 programmable scenes, ability of up to 100 steps per scene
Assignable fade setting separately and Master control
Infrared remote control function
MASTER/FADE
60s 600s
0
One preset pattern available for per scene
With a Signal/Power Distribution Box as tension provider and DMX
signal converter in the entire system
US and EU versions optional
2.Control Panel View
Front Control View
X-Fade-6
Channel Faders(1~6):
Used to control the output level of each corresponding fixture channel.
Master Control Fader:
Used to control the overall output level for all Channels1~6 or control the master level for all Scenes.
Scene LED indicators(1~6):
These 6 LED's detail the current fader level for Scene's1-6. The LED indicators will reflect the fader
level changes in real time.
SC1
SC2
SC4
SC5
OFF
UP
OFF LED indicators:
To indicate the output state is turned on or off.
SC3
SC6
DOWN
CH.3
Scene Buttons(1~6):
To select the corresponding programmed scene to playback.
CH.1
CH.4
CH.2
CH.5
OFF Button:
To press the OFF button to close all channel1-6 output or enter/exit Recording Scene Mode.
CH.6
MASTER
Infrared Sensor:
To receive infrared remote control signs from Infrared Remote.
RJ45 Interface:
To link with the Signal/Power Distributor Box via C-LAN cable for getting the tension and DMX
output.
Infrared Remote
3.Operating Guide
3.1Recording Scenes
3.1.1 Recording Scenes Mode enables: press and hold the "OFF" button down for approximately 2 seconds or until the red
LED indicator next to the "OFF" button comes on, once the indicator is flashing, Record mode is engaged and you may
release the "OFF" button.
3.1.2 If the selected scene has been stored before, its indicator will be on. Press and hold the "Scene" button down for about
2 seconds and all LED indicators will flash repeatedly 3 times to delete it.
3.1.3 Select the "Scene" button where you wish to record to. The selected "Scene" LED will flash repeatedly.
3.1.4 Adjust the corresponding "Channel Fader" all ways up to ten(10) to set the desired fader level for the step of the scene.
Once you're satisfied with the setting, press the "Scene" button to store it. All LED indicators will flash repeatedly 3 times,
indicating that your the step of the scene has been recorded.
3.1.5 Repeat Step3.1.4 to record more steps for the scene, up to 100 Steps can be created per scene.
3.1.6 To record additional scenes, repeat Step3.1.3~3.1.5.
3.1.7 Once you've stored all of your scenes, press and hold the "OFF" button to exit. A blue LED next to the "OFF" button coming
on is indicative that you are out of the Recording Scene mode.
-Page 1-
5.System Connection Diagram
AC 120V / 230V, 60/50Hz
0.5A max.
6 channel DMX output
Standard DMX cable
C-LAN cable
PIN-CONNECTION of RJ45 Interface
1. DMX OUT +
2. DMX OUT -
3. DMX IN +
4. GND
Remote Control
5. GND
6. DMX IN -
7. +12V
8. +12V
NOTE:
Effective distance from the infrared sensor of X-Fade-6 to Infrared Remote shall be limited within the range of 10m.
Otherwise, it results out of control.
Acclaim Lighting-Los Angeles, CA90058
24-004-1999-00
Rev1.3
-Page 3-
|