CC-IRC
Infrared Emitter
Download from Www.SomanuCalso.cnomt.rAoll MlaSnuyalsstSeeamrch AAndcDcoewnslosaod.ries
CC-IRC IR Emitter Overview
The IR Emitter adheres directly to the IR control window of your
equipment by using clear two-sided tape to securely adhere the opaque
shield. This “standard configuration” allows you to control your equipment
either from either IR emitters or a hand-held remote control.
The two black adhesive-backed window shields (Figure 3) are included
within each emitter package and allow for alternate configurations. With
this shield (surrounding the internal emitter), you can restrict IR reception
through the device’s control window by blocking any interference or IR
signals produced by sources other than the internal emitter. Without this
shield, any incoming IR signal can pass through to the IR control window
and overlap signals sent via the emitter (Figure 1).
Note: Each CC-IRC package is shipped with four sealed alcohol pads
which can be used to clean any adhesive residue left from a previous
installation of the window shield on the surface of a device’s IR
control window.
Pass-Through Configurations
This method allows IR signals generated from hand-held remotes to easily
pass through the opaque red shell/cover. The internal IR LED can be
oriented to either face towards or away from the shell (Figure 1),
depending on its output configuration. Use the low-output configuration
when device is being saturated by an IR signal. Use the high-output
configuration when the device isn’t receiving enough of an IR signal and
requires more strength. The side with the round “bump” is the high-output
side.
Low-Output
High-Output
Towards
IR window
Away from
IR window
Adhesive
Download from Www.Somanuals.Fciogmu.rAell1Manuals Search And Download.
Removing the Factory-Installed Shell
The factory-installed shell
is easily removed by
carefully separating the
two halves with a
sharp-edged tool, such as
an X-Acto™ knife.
The IR LED can then be
reversed or removed
when the shell is
Figure 2
separated. Once the IR emitter and/or shield
installations have been completed, the housing
can be re-assembled by pressing the two halves
firmly together.
Shielded Configuration
Use this configuration to prevent interference from fluorescent lights or
other IR sources. The metallic shield prohibits passage of external IR
signals and ensures proper IR signals will be received from the emitter.
1. Remove the IR LED from the factory-installed shell (Figure 2).
2. Test fit the location and size of the IR shield (Figure 3) on the target
device. If necessary, use scissors to trim the shield to fit the opening
of the IR window.
3. Remove the adhesive backing from the IR shield and carefully place
the IR LED into the recessed area using the correct orientation
(Figure 1). Make sure the wires attached to the IR LED are not
shorted together.
4. Flip the shield-emitter combo back over and begin to carefully position
the shield over the IR control window so that it covers the entire
surface (Figure 4). This keeps any other signal from coming through.
5. Press firmly on the shield surface to activate the pressure-sensitive
adhesive.
Opaque IR Window Shield
Figure 3
Cable Assembly
IR Input Control Window (on device)
IR Emitter Shield
IR Emitter
Controlled Equipment
(DVD, CDP, VCR, etc.)
Figure 4
AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under
normal use for three (3) years from the date of purchase from AMX Corporation, with the
following exceptions:
•
•
•
Electroluminescent and LCD Control Panels are warranted for three (3) years, except for
the display and touch overlay components that are warranted for a period of one (1) year.
Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are
warranted for a period of one (1) year.
Unless otherwise specified, OEM and custom products are warranted for a period of one
(1) year.
•
•
AMX Software is warranted for a period of ninety (90) days.
Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an
Authorized AMX Dealer. All products returned to AMX require a Return Material Authorization
(RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA
number must be clearly marked on the outside of each box. The RMA is valid for a 30-day
period. After the 30-day period the RMA will be cancelled. Any shipments received not
consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible
for products returned without a valid RMA number. AMX Corporation is not liable for any
damages caused by its products or for the failure of its products to perform. This includes any
lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is
not liable for any claim made by a third party or by an AMX Dealer for a third party. This
limitation of liability applies whether damages are sought, or a claim is made, under this
warranty or as a tort claim (including negligence and strict product liability), a contract claim, or
any other claim. This limitation of liability cannot be waived or amended by any person. This
limitation of liability will be effective even if AMX Corporation or an authorized representative of
AMX Corporation has been advised of the possibility of any such damages. This limitation of
liability, however, will not apply to claims for personal injury. Some states do not allow a
limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the
limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the
owner specific legal rights. The owner may also have other rights that vary from state to state.
The owner is advised to consult applicable state laws for full determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES
NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX
CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED
TO THE TERMS OF THIS LIMITED WARRANTY.
93-0000-11 Rev E
041-004-2606 2/06
©2006 AMX Corporation.
All Rights Reserved.
All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the
light bulb icon are all trademarks of AMX Corporation.
AMX reserves the right to alter specifications without notice at any time.
*In Canada doing business as Panja Inc.
3000 research drive, richardson, TX 75082 USA
469.624.8000 • 800.222.0193 • fax 469.624.7153
technical support 800.932.6993
brussels • dallas • los angeles • mexico city • philadelphia • shanghai • singapore • tampa • toronto* • york
|