33620 DK-M
Electric Ceramic Hob
Operating Instructions
Congratulations from AEG
Dear Customer,
Congratulations with your new Hob.
It is important that you become familiar with the functions and features of
the Hob. You should therefore read these operating instructions as they will
help you get the most out of your new Hob.
Pay extra attention to sections marked
you avoid accidents.
. These are warning texts to help
Keep the operating instructions. They will come in handy if there is
something you are not sure about, and should accompany the Hob if it is
transferred to a new owner.
The structure of the operating instructions enables you to use them as a
reference manual. The first part of the operating instructions contains a
general description of your new product. Then follows a short introduction
of the things to do before you use the Hob for the first time. The section
“How to use” describes how the Hob is used in everyday life. Use this
section until you are familiar with your new Hob. The section “Cleaning
and Maintenance” provides information on both daily and more thorough
cleaning of the individual components of the Hob. Should problems arise
when you use the Hob, you can look in the section “Before calling service”,
where there are instructions on how to remedy some practical and technical
problems yourself.
Enjoy!
Regards,
Table of contents
Contents
Page no
For the user
Congratulations from AEG......................................................................... 3
Safety information ........................................................................................ 5
Description of the product ......................................................................... 6
How to use .................................................................................................... 7
Pilotlight ................................................................................................ 8
Residual-Heat indicator ........................................................................ 8
Advice and hints for using the cooking zones....................................... 9
Cleaning and maintenance of ................................................................... 11
Stainless steel surfaces ....................................................................... 11
Theceramicglasshob ........................................................................ 11
Tips on the use of the ceramic hob unit .............................................. 12
For the installer
Installation .................................................................................................. 14
Electrical connection................................................................................... 15
Building in dimensions
.......................................................................... 17
Technical Data ........................................................................................... 19
How to read the operating instructions:
1... 2...Step by step
Safety information
Hint and tips
Environmental information
Safety information
These warnings are provided in the
interests of your safety. Ensure you
Never leave the hob unattended while
deep fat frying, or heating fats and oils.
fully understand them before installing
or using the appliance. Your safety is of The appliance is not intended for use
paramount importance. If you are
unsure about the meaning of these
warnings contact the Customer Care
Department for assistance.
by young children or infirm persons
without supervision.
Child Safety
Young children should be supervised
to ensure that they do not play
with the appliance
Installing
Do not install the hob if the ceramic
glass is damaged or cracked.
The hob gets hot when it is in use.
This hob must be installed according to Children should be kept away until the
the instructions supplied. Any
hob has cooled.
installation work must be undertaken
by a qualified competent person.
Maintenance and Cleaning
Only clean this hob in accordance
with the instructions given in this
book.
Do not alter the specifications or
attempt to modify the appliance in any
way.
Service
During Use
Repairs carried out by inexperienced
persons may cause injury or serious
malfunction of the appliance. Repairs
must only be carried out by a
qualified/competent person. Contact
your local AEG Service Centre.
The hob is intended for domestic
cooking only. It is not designed for
commercial/industrial purposes.
Ensure that all the control knobs are in
the OFF position when not in use.
Disposal
Make the hob unusable by cutting off
the cable.
Do not use the hob if it is damaged in
any way, contact your local AEG
Service Centre.
Dispose of any packaging material and
old appliances at an authorised
disposal site.
Never use plastic or aluminium dishes
on the hob.
5
Description of the product
Rear cooking
zone
Residual heat
indicator
Front cooking
zone
Control knobs
Pilot light
6
How to use
Control knob (to the left)
Control knob for regulating the
plate at the rear
Control knob for regulating the
plate at the front.
The regulating of heat is graduation-free
for both plates on a scale from 1 to 3.
“1”
“3”
“0”
Represents lowest heat
Represents maximum heat.
Represents “OFF”.
0
0
3
3
1
1
2
2
Control knobs
Pilot light
Do not use the ceramic hob if the
glass is damaged.
If a fault or crack appears during
cooking disconnect the hob
immediately and contact AEG
Service.
7
Pilot light
Pilot light is activated when either of
the zones are turned on, and will
remain on until the cooking zones are
switched off.
Residual-Heat indicator
Each plate has a residual heat
indicator which remains on as long as
the temperature of the cooking zone
exceeds 80˚C, even if the cooking zone
is switched off.
Settings for ordinary cooking zones
Step
Function
0
·
The cooking zone is switched off
Keeping warm
1
Gentle simmering
·
Simmering
2
Frying / browning
· - 3
Bringing to the boil / quick frying / deep-
frying
This table should be used as a guide only. The settings
depend on the saucepan you use, quantity and contents. After
a while you will learn to choose the correct settings. See also
the section “Advice and hints for using the cooking zones”.
8
over will burn onto the hot
cooking zone.
Advice and hints for using the
cooking zones
If you use the advice below
you will save energy and
make your cleaning tasks
easier.
Saucepans with very
shiny/bright bases will
prolong the cooking time
slightly compared with
cooking utensils with
matt/dark bases.
Adjust the cooking zones
correctly. Select the highest setting
for the cooking zones until the food is
brought to the boil. Then reduce the
setting as far as possible, without the
food going off the boil.
Use a tightly fitting lid on the
saucepan. Without a lid you
use more than three times as
much electricity.
Use level saucepans. An
uneven saucepan may
increase the electricity
consumption by up to 50 per
cent. Check whether your
saucepans have level bases
by placing the item in question
upside down on a work top and
positioning a ruler on the base.
A curved base, both inwards and
outwards, will prolong the
cooking time and increase the
energy consumption
The saucepan should match
the cooking zone – or be
slightly larger. Remember
that a large saucepan can also
hold small quantities. If the
diameter of the base is too small,
the energy consumption will
increase, and any food boiling
9
Check whether your cooking utensils
has level bases by placing the item in
question upside down on a work top
and positioning a ruler on the base. A
curved base, both inwards and
outwards, will prolong the cooking
time and increase the energy
consumption. If the diameter of the
base is too small, the energy
consumption will increase, and any
food boiling over will burn onto the
hot cooking zone.
Cooking utensils with very
shiny/bright bases will prolong the
cooking time slightly compared with
cooking utensils with matt/dark bases.
10
Cleaning and maintenance of
3. Wipe the ceramic hob clean with
For reasons of hygiene and
a damp cloth or kitchen roll.
safety, the cooking zones
Tough stains can be removed by
must be kept clean. Grease
rubbing the stain hard with
stains and spilled food
kitchen roll.
4. Wipe off remaining cleaning
agent with a damp cloth.
5. Wipe with a dry cloth, if
required.
generate smoke when heated,
and can even cause fire.
Make sure that the ceramic hob is dry
when you heat it up again. Ceramic
hobs can develop rainbow-like stripes
if heated while damp.
Never use metal wool, metal sponges
or other abrasive cleaning agents.
The ceramic glass hob
Immediately scrape off stains caused
by food which has boiled over using
the scraper supplied with the hob,
spilled sugar, dishes containing sugar
(jam, juice, etc.), melted plastic and
aluminium foil while the ceramic hob
is still hot. If the ceramic hob is
allowed to cool it may become
Stainless steel surfaces
Clean the appliance after use with a
soft cloth well wrung out in warm
water, use a small amount of liquid
detergent for stubborn soiling.
Stainless steel parts may become straw
coloured with use, use a proprietary
stainless steel cleaner to remove this
straw discolouration.
damaged. A dirty ceramic hob
decreases the heat transfer between
cooking zones and cookware.
After use the cooking zones should be
wiped with a damp cloth with washing
up liquid. For severe soiling you can
follow these steps:
1. Remove stains etc., with the
ceramic hob scraper.
2. Make sure that the ceramic hob
has cooled down. Use a ceramic
cleaning agent, such as vitroclen.
11
Tips on the use of the
ceramic hob unit
Do not slide saucepans across the
surface of the hob - always lift the pan
when placing it on, or removing it
from the ceramic surface.
Wipe the bottom surface of the pots
and pans with a clean dry cloth before
placing them on the ceramic surface.
This helps to reduce cleaning and
prevents scratching the hob glass.
Wipe off spills whilst the hob is warm.
Select the highest setting for the
cooking zones until the food is brought
to the boil, then reduce the setting.
Use saucepans with an even base. An
uneven based saucepan may increase
the electricity consumption by up to
50%.
The saucepan should match the
cooking zone or be slightly larger.
Use a tightly fitting lid on the saucepan
to reduce electricity consumption.
NO
NO
YES
12
The decorative pattern on the ceramic
surface can become scratched and
marred with use, depending upon
maintenance, but does not adversely
affect performance.
Such blemishes are not covered by the
warranty and do not affect the
operation of the hob.
Spills and melts must be removed
immediately, while the surface is still
warm, using the scraper supplied with
the unit. Especially damaging are melted
plastic, aluminum, or any foodstuff
containing sugar, including natural sugar,
as these can create permanent
“pockmarks” and craters on the ceramic
surface. After scraping polish thoroughly
with the cleaning agent supplied with the
unit.
Utensils which have been in contact with
the above-mentioned melted materials
must be cleaned throughly before used
again on the ceramic-top hob unit.
Defects in the ceramic surface which can
be related to the above are not covered
by the warranty.
Warning:
Aluminum foil and plastic utensils are
not to be placed on hot surfaces.
The surface may not be used for storage.
Do not stare at the heating units when
in operation.
13
Installation
Warnings about electrical connection
l
Any electrical work required to install this hob should be carried out
by a qualified electrician or competent person, in accordance with
the current regulations.
l
Before the appliance is connected:
1) check that the main fuse and the domestic installation can support
the load;
2) check that the power supply is properly earthed in compliance with
the current rules;
3) check the socket or the double pole switch used for the electrical
connection can be easily reached with the appliance built in the
forniture unit.
l
This hob is designed to be connected to a 230V single-phase 50 Hz AC
220 V, 60 Hz electrical supply.
l
This hob has been registered as a “Class Y” appliance according to
Fire Risk Protection Regulations. It can be built-in in furniture units
placed near higher walls or units, provided that one of the sides is
adjacent to an unit with the same height.
l
If connecting the hob directly to the power mains, a double pole
switch should be fitted, with a minimum gap of 3 mm. between the
switch contacts and of a type suitable for the required load in
compliance with the current electric regulations. The switch should
be sited within 2m of the hob and be easily accessible upon
completion of the installation.
l
Proper arrangements must be taken in designing the furniture unit,
in order to avoid any contact with the bottom of the hob which can
be heated when it is operated. Before any intervention, ensure the
hob is disconncted from the electricity supply.
l
l
l
Once connection has been carried out, test heating elements for
about 3 minutes.
The minimum distance combustible material can be fitted above the
hob in line with the edges of the hob is 420 mm.
It is not allowed to install an oven under the hob.
14
Electrical connection
This hob is provided with a connection cable type H05 V2V2-F T90,
2
section 3 x 1,5 mm
. A suitable plug must be fitted to the cable and
then connected to a suitable plug, according with spexcification given
on the rating plate.
If connectiong the hob directly to the power mains, a double pole
switch should be fitted, with a minimum gap of 3 mm. between the
switch contacts and of a type suitable for the required load in
compliance with the current electric regulations.
The switch must not break the yellow and green earth cable at any
point.
Ensure that the hob supply cord does not come into contact with
surfaces whose temperature exceed 90°C over room temperature..
Replacement of connection cable
The connection of the voltage cable to the appliance's terminal block
is of type "Y". This means that its replacement requires the specific
equipment of a technician.
In this case, only cable type H05V2V2-F T90 must be used. The cable
section must be suitable to the voltage and the working temperature.
The yellow/green earth wire must be approximately 2 cm. longer than
the phase wires .
15
Warnings about building in the hob
l
Ensure the eventual plastic covering of the furniture unit has been
fixed with a heatproof adhesive (100°C heatproof).
l
Fitting of solid wood panel borders on the working top or behind the
hob is allowed provided that minimum distances are observed.
l
l
A insulation panel which can only be removed with tools must be
fitted under the hob at a minimum distance of 50 mm.
If the hob must be installed beside a cupboard, ensure a minimum
distance of 40 mm. is observed and the side of the cupboard is
covered with heatproof material.
l
l
Before making the cut out in the worktop ensure that the edges of
the hob that are to be near the rear wall have a minimum distance
of 55 mm.
Aminimum distance of 100 mm. must be observed between the hob
and an eventual side wall exceeding the working top height.
l
l
Hanging furniture units or cooker hoods must be fitted at a
minimum height of 650 mm. from the hob.
Combustible or not heatproof materials must be kept away from the
appliance.
16
Building in Dimensions
Cut Out Size
The dimensions of the cut-out are given in the diagram.
If 30 cm. hobs with different functions must be built in one beside the
other (e.g. 2 Plate Hob + 2 burners Hob), the minimum distance shown
in the diagram must be observed.
17
Securing the hob into the cut out
Before fitting the hob into the cut out, the sealing gasket supplied with the
hob must be fitted to the edge of the cut out. It is essential that no gaps are
left in this seal in order to prevent spillage near the hob seeping into the
cabinet below.
1) Place the sealing gasket (A)
all around the edge of
the cut out.
2) Fit the hob in the cut out
and push it down until
it comes in contact with
the kitchen top surface.
The remove the excess
sealing.
3) To remove the hob from
the cut-out, lift the edge
of the hob by means of
the edge of a screw-
driver.
Proper arrangements must be taken in
designing the furniture unit, in order to
avoid any contact with the bottom of the
hob which can be heated when it is
a
Removable
operated.
panel
The recommended solution is shown in
diagram.
The panel fitted under the hob should be
easily removable to allow easy access if
technical assistance is needed.
Technical data
Dimensions in mm:
Hob H x W x D
Cut Out W x D
8 x 290 x 510
270 x 490
Heating Elements Ratings in Watt:
Front Hotplate Ø 145 mm.
Rear Hotplate Ø 180 mm.
1200
2900
Total rating in Watt
Electrical supply
3000
230 V, 50 Hz
This appliance is manufactured according to the following EEC
directives:
73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC current edition.
19
Servicing
If you are not able to find any hint for a fault in this Instruction Book,
you should contact our After-sales Service.
When calling for an engineer, please remember you will be requested
to specify the following data:
E-Nr. _______________________
F-Nr. _______________________
which are quoted on the label attached on the back cover of this
Instruction Book.
These data enable the After-sales Service to make a focused spare part
specification, so that your hob can be repaired at the first engineer
visit.
This will save you the additional costs of any possible repeated visits
by the After-sales engineer.
AEG Hausgeräte GmbH
ꢀ
ꢀ
© Copyright by AEG
Sie können Ersatzteile, Zubehör und Pflegemittel
35688-6104
05/04
|